elecbuy
137.5MHz~2.7GHZ UV RF Vector Impedance ANT SWR Antenna Analyzer Replace N1201SA
UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz is Pro Tool to test our DIY Antenna for DJI Phantom Inspire MAVIC. It is a must tool for all DIY DJI Phantom Inspire MAVIC Pilot.
- This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration
- The default boot into single-point measurement interface.
- The default boot into single-point measurement interface.
Specifications:
- Model: PS100
- Working currency 137.5MHz~2700MHz
- Stepped frequency 1kHz
- Display 2.4cun TFT trdp
- Resolution ratio 320*240(QVGA)
- Battery capacity: 2000mAH(7.4Wh)
- Power consumption <1.5W
- Charge current 400mA
- Charge port USB
- Auto power off can be set 5-60minutes
- Measured parameters resistence reactance standing wave s11
- Resolution ratio 4 number
- Frequency accuracy about 5ppm
- Connector SMA-K
- Impedance measurement range: 0.1~1000
- Standing wave measurement range:1.000~65
- S11(dB)measurement range: 0dB~-60dB
- Working temperature:0~40 degree
- Atmospheric pressure:860hPa~1060hPa
- Model: PS100
- Working currency 137.5MHz~2700MHz
- Stepped frequency 1kHz
- Display 2.4cun TFT trdp
- Resolution ratio 320*240(QVGA)
- Battery capacity: 2000mAH(7.4Wh)
- Power consumption <1.5W
- Charge current 400mA
- Charge port USB
- Auto power off can be set 5-60minutes
- Measured parameters resistence reactance standing wave s11
- Resolution ratio 4 number
- Frequency accuracy about 5ppm
- Connector SMA-K
- Impedance measurement range: 0.1~1000
- Standing wave measurement range:1.000~65
- S11(dB)measurement range: 0dB~-60dB
- Working temperature:0~40 degree
- Atmospheric pressure:860hPa~1060hPa
Advice When Using:
- In order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
- Try to use good quality RF cable and connectors.
- Calibrated cable marked to the next may not need to calibrate and direct use.
- Test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
- Measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
- If the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis.
- In order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
- Try to use good quality RF cable and connectors.
- Calibrated cable marked to the next may not need to calibrate and direct use.
- Test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
- Measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
- If the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis.
Notes:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
Package include:
1 x PS100 UV RF Vector Impedance ANT SWR Antenna Analyzer Meter
1 x User Manuel
1x Charge cable
1 x PS100 UV RF Vector Impedance ANT SWR Antenna Analyzer Meter
1 x User Manuel
1x Charge cable
We accept PayPal only.
1.Items are shipped from china.we will send out within 1 bussiness day after receive the payment.
2.We only ship to ebay confirmed address. So before bidding, please kindly verify your ebay address.
3.Shipping to USA takes 8-18 days in normal condition by E-packet with tracking number.
Shipping to most other countries takes about 12-30 days via Economy Int'l Airmail.
Less than $40, without free tracking number,if you request tracking number,please send ebay message to us.
Over $40,with tracking number free.The shipping time depends on your location and local postal service,as well as the weather condition along the shipping,sometimes may take longer,.please send ebay message to us if you didn't get your package.
4.Express shipping: Extra $20 --$25 will be charged for the first 500 grams for most countries. Send ebay message to us if you need this service.
1.If you are not satisfied when you receive your item, please return it within 30 days for a replacement or money back. Please send ebay message to us before you return it.
2.If item is defective in 30 days, We will send you a replacement without extra charger, or offer refund after we receive the defective item.
3.If item is defective after 30 days, you can still send it back to us. We will send you a new one after receiving the defective item. But you have to pay the extra shipping fee.
We are honest seller and do our best to serve you.
So if you have any concerns,please don’t hesitate to send ebay message to us.