Other MAX ACR A/B Resin Application

ARTIFICIAL REEF CONSTRUCTION Click On Picture To View Video MAX ACR AQUARIUM SAFE CONSTRUCTION EPOXY RESIN - YouTube Video will open in a new window [isdntekvideo] Determine the volume or size of the artificial reef and have a rough idea of the shape desired in mind.  In this procedure, a standard 3-inch thick, 2 pounds per cubic foot EPS Styrofoam sheets were bonded together to create a thick block 4 layers thick for the front and 2 layers for the sidewall to create an “L- shape” blank. This type of foam can be purchased from any hardware centers in 4 x 8 sheets and are commonly used for insulation.  Mixing Epoxy ResinsPlease view the following video for the proper mixing of epoxy resins.  It demonstrates the proper technique of mixing any type of epoxy resin system. The proper cure and final performance of any epoxy resin system are highly dependent on the quality and thoroughness of the mix.The resin and curing agent must be mixed to homogeneous consistency to achieve full cure. Avoid Tacky Or Uncured Spots Video will open in a new window PROPER MIXING TECHNIQUE How To Mix Epoxy Resin For Food Contact Coating. Avoid Tacky Spots, Minimize Air Bubble When Mixing - YouTube Video will open in a new window Using the eBay App? Paste link into a browser window: [isdntekvideo] RECOMMENDED MIXING PROCEDURE MAX ACR will require complete and uniform incorporation of the resin and curing agent. Poorly mixed batches will result in tacky spots, uneven surface, poor adhesion and other detrimental effects. The mix ratio between the resin and curing agent is fixed and reducing or increasing the established ratio will not increase or decrease the cure rate. Physical and mechanical results will differ as stated below if this ratio is altered. To ensure trouble-free results follow this mixing procedure.  Determine the volume needed and weigh out or proportion out two parts “Part A” to one part “Part B” by weight or by volume into a clean container. Mix using a spatula in a gentle folding method to avoid excess air entrapment. Scrape the sides and bottom of the container and mix for approximately 1 minute.To ensure complete mixing, transfer the mixed resin into another container and continue mixing for another 30 seconds. Dispense the mixed resin from this container. Use the mixed resin within the specified working time. To create colors use epoxy compatible colorants such as MAX EPOXY COLORANTS can be added (5% maximum) to create translucent to opaque colors.Other solid fillers such as calcium carbonate, silica sand, and clay can also be incorporated.The addition of fillers and colors should be done to the resin side or PART A and allowed to self-degas by placing the mixture in a hot water bath (120°F- 150°F) for 2 to 3 hours. and allowed to cool to room temperature. Any entrapped air bubbles will rise to the surface and can be removed by gentle surface mixing.  Add the curing agent when the resin has cooled. Solvents such as acetone can be used sparingly to help further reduce the viscosity and aid in the application; the acetone will evaporate before the epoxy resin cures to a hard finish.Use an accurate scale if available but volumetric measuring can also be utilized as long as the mix ratio between the resin and curing agent is carefully maintained.  The Use Of A Weighing Scale Is Highly Recommended To Ensure Proper Cure Use A Digital Scale. Purchase this scale with any of product offering and the shipping cost of the scale is free. Please request a total before paying for combined shipping savings. https://www.ebay.com/itm/222630300203 COLOR ADDITION DEMONSTRATION Video will open in a new window

Sample Formula: Opaque Coating or Casting Part A MAX ACR Resin 100 grams Calcium Carbonate Marble Epoxy Powder Epoxy Filler 325 Mesh 50 grams MAX EPOXY COLORANT 3 grams  Premix the Color Paste first with the MAX ACR PART A until well dispersed and then add the calcium carbonate and mix until a uniform consistency is achieved. Allow the mixed resin to de-gas at room temperature or soak the container in a warm water bath and then allow to cool before adding the curing agent. Add the adjusted amount of Curing Agent and mix as described above. Part B MAX ACR Curing Agent 50 grams

CALCIUM CARBONATE   https://www.ebay.com/itm/311946636393

MAX EPOXY COLOR KIT  https://www.ebay.com/itm/311946633043

ARTIFICIAL REEF CONSTRUCTION

Pre- Cut the foam to the desired size and basic shape and remove the protective skin. Bond the sheets using MAX ACR to create workable block medium and Allow to cure for 24 hours. Fill a spray bottle (HDPE plastic bottle) with acetone and adjust output spray to a fine mist. Mist over the surface of the foam block to soften the surface Gouge out chunks from EPS foam block to create the desired shape and contour. Continue using the acetone mist to melt the EPS foam to achieve a rough texture. Note how the adhesive bond line used to bond the sheets begins to act like strata layers after the acetone has melted. Allow the acetone and EPS FOAM to outgas for 24- 36 hours. Placing the foam under direct sunlight will accelerate outgassing of any residual solvent. Mix 200 grams of MAX ACR PART A to 100 Grams of MAX ACR Part B in a clean container. Apply the coating onto the foam to create the primary barrier coating. Color can be added at this point to help determine complete coverage of the foam. Allow curing for 24 hours. Inspect the entire surface of the foam to ensure complete coverage. Repeat Step 8 thru Step 10 but omit the acetone addition and add a more colorant to distinguish first coat from the second application. This technique will give the foam further depth of field. Apply the coating onto the foam and allow to cure. The surface is now noticeable harder. Allow curing for 2 to 3 days to allow full outgassing and cure of the MAX ACR. Placing the foam under direct sunlight will accelerate the cure and any solvent outgassing. After the MAX ACR has fully cured, the foam surface has now developed a very rigid shell. Rinse the entire surface with warm water several times and allow it to completely dry. The artificial reef is now ready to be bonded to the aquarium to secure it in place. If a permanent bond is desired, use the MAX ACR as an adhesive and bond it directly to the aquarium floor and sides. If a temporary removable bond is desired use aquarium safe silicone adhesive and bond it directly to the aquarium floor or underground filtration plate.  Conditioning the MAX ACR artificial reef After 36 hours of curing, fill the aquarium with warm water and lightly scrub the entire surface area.  Drain the aquarium and repeat this process for at least 3 times. Do not use soaps or detergents, just warm water or aquarium safe cleaner. Fill the aquarium with water and begin water conditioning process. Allow the filled aquarium to stabilize in temperature. If the water becomes cloudy, drain the aquarium once more and repeat cleaning process. Place the live fish into the aquarium only when the water color and pH has stabilized for 24 hours.   Cleaning The constructed reef can be cleaned using aquarium safe cleaners or by scrubbing with a soft brush and water.  Safe to use on both fresh/salt water.

MAX ACR A/B is a specially formulated epoxy resin designed specifically as a construction resin for artificial pond and aquarium building applications. It can be used as a coating for waterproofing plywood, impregnating or laminating resin of fiberglass for structural support, structural adhesive and a specialty resin for simulated coral reef building.   Upon cure MAX ACR A/B is inert and will not leach out any chemicals that can pollute and contaminate the contained water. It demonstrates low extractable compounds; tested against the strict standards of ASTM E595, which measure extractable matter or collectible volatile condensable matter (CVCM) under forced vacuum extraction. MAX ACR is an excellent choice all types of bonding, coating, casting and other aquarium or safe water containment applications.   AQUARIUM DECORATIONS PROTECTIVE COATING

DRIFTWOOD HERMETIC SEALED WITH MAX ACR FOR AQUARIUM SAFE DISPLAY           MAX ACR A/B is 100% reactive epoxy resin and curing agent and contains no free silicone additives. MAX ACR will require a minimum of 3 days of curing at room temperature 75°F to ensure that the epoxy is fully reacted. USE AN INFRARED HEAT LAMP FOR LARGER PARTS. RESIN SYSTEMS AT OUR eBay STOREFor our complete listing, please Visit our eBay store! DON'T FORGET OUR EPOXY MIXING KIT Click The Link To Add To Order  https://www.ebay.com/itm/222623932456 EVERYTHING YOU NEED TO MEASURE, MIX, DISPENSE OR APPLY  Proportioning the correct amount is equally as important to attain the intended cured properties of the resin system. The container in which the epoxy and curing agent is mixed is an important consideration when mixing an epoxy resin system. The container must withstand the tenacity of the chemical and must be free of contamination. Most epoxy curing agent has a degree of corrosivity, as a general practice, protective gloves should be worn when handling chemicals of the same nature. MIXING KIT CONTENTS  1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams    4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups 4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix Cups One Size Fits All Powder-Free Latex Gloves  2 Each Graduated Syringes Wooden Stir Sticks Foam Brushes   IMPORTANT NOTICE Your purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product. The user should thoroughly test any proposed use of this product and independently conclude the satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval. The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and  Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use. There is no warranty of merchantability for fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.