MAX MCR A/B
POTTING RESIN FOR ELECTRONIC CIRCUIT BOARDS
48- FLUID OUNCES COMBINED VOLUME
1 Quart Of Resin (32 Fluid Ounces)
And
1 Pint Of Curing Agent (16 Fluid Ounces)
PRODUCT DESCRIPTION
MAX MCR BLACK A/B is an unfilled medium working time, low viscosity potting compound resin system for embedding or encapsulating printed circuit boards (PCB), relays, coils, and other electronic or electrical circuitry. MAX MCR A/B is low in viscosity and is room temperature cured. It is mixed 2:1 by weight or by volume and provides a 30 minute working time (200-gram mass @ Upon cure, MAX MCR is completely noon electrically conductive offers a very high gloss finish blemish free surface. It cures to a hard but tough compound that is suitable for small to medium parts without excessive exothermic heat generation (up to 1 pound). It has a 30-minute working time when mixed up to 200-gram mass.
The 2 to 1 mix ratio offers ease of use and easily poured in place or can be adapted for mix meter equipment.
MAX MCR A/B bonds to PVC, PP, ABS, Plastisol, aluminum, steel, copper, brass and other materials typically used in electrical circuits.
RoHS & REACH Conflict Minerals Compliant
Electrical Insulating And Potting Of Electronic Circuitry
Permanent Opaque Black Masking Compound For Proprietary Electronics
Electrical Potting Compound
Embedding Or Masking Compound
Waterproof Low To High Voltage Circuit
Electrical Insulating And Potting Of Electronic Circuitry
Permanent Opaque Black Masking Compound For Proprietary Electronics
Circuit Board Conformal Coating
Electrical Potting Compound
Waterproof For Continuous Salt Or Fresh Water Immersion
Low To High Voltage- AC/DC Circuit
Direct Cast (No Box Enclosure) LED Driver Circuit Board Potting Using Silicone Mold
Form And Color | Black Liquid, Self Leveling Other Colors Available |
Viscosity Part A | 2,500 cPs @75°F |
Viscosity Part B | 750 cPs @75°F |
Mixed Viscosity | 1,950 cPs @75°F |
Mix Ratio By Weight | (2:1) 100 Parts A to 50 Parts B |
Mix Ratio By Volume | (2:1)100 Parts A to 50 Parts B |
Mixed Density | 1.10 g/cc |
Working Time | 30 minutes (400-gram mass) |
Gel Time | 60 minutes @75°F |
Peak Exotherm | 280°F max (400-grams) |
Demold Time | 24 hours room temperature @75°F |
Accelerated Cure | 2 Hours @75°F +30 minutes @200°F |
Shore Hardness | 75 Shore D |
Shrinkage: | <0.30 % |
Compressive Strength | 13,800 psi @75°F |
Tensile Strength | 9,900 psi @75°F |
Tensile Elongation | 4% @75°F |
Heat Distortion Temperature | 190°F |
ELECTRICAL AND THERMAL CONDUCTIVITY PROPERTIES
Volume Resistivity | 4.7 X 1013 Ohms-Cm |
Dielectric Strength | 510 Volts/Mil 60 Cycles |
Dielectric Constant | 4.0 (10 kHz) |
Dissipation Factor | 0.014 (10 kHz) |
Thermal Conductivity (Unfilled) 40°-45°C | 0.25 W F/mK |
CHEMICAL RESISTANCE PERFORMANCE
FULL IMMERSION AT 25°C
MEASURED PERCENT CHANGE IN WEIGHT
Reagent | 10 days | 28 Days |
Deionized Water | 0.03 % | 0.03 % |
Sea Water | 0.01 % | 0.08 % |
Methanol | 0.93 % | 2.41 % |
Ethanol | 1.98 % | 1.28 % |
Toluene | 0.40 % | 2.86 % |
Xylene | 0.04 % | 0.05 % |
Gasoline (E85 Blend) | 0.10 % | 0.23 % |
Dimethyl Formamide | Destroyed | Destroyed |
10% Lactic Acid | 0.81 % | 1.42 % |
10% Acetic Acid | 0.11 % | 0.45 % |
70% Sulfuric Acid | 0.08 % | 0.14 % |
50% Sodium Hydroxide | 0 % | 0.1 0% |
10% Sodium Hypochlorite | 0.51 % | 0.96 % |
MAX MCR A/B Available Kit Sizes
48-Fluid Ounce Combined Volume: https://www.ebay.com/itm/223885745256
96-Fluid Ounce Combined Volume: https://www.ebay.com/itm/311946513165
192-Fluid Ounce Combined Volume: https://www.ebay.com/itm/311960933510
High-pressure Sensors Potted With
MAX MCR A/B
24 Volt Solenoid Valve Potted With MAX MCR A/B
Tested To >2,000,000 Cyclic On/off Test With No Failure
.
Circuit Board Potting With MAX MCR A/B
Waterproofing Of An Electrical Circuitry
Click The Picture To View The Video
MAX MCR A/B used as the black PCB potting compound.
The clear resin used as the LED encapsulant is our MAX DIAMOND CLEAR,
a cycloaliphatic epoxy resin that is resistant to damage and yellowing from the UV energy produced by the LED light.
It demonstrates excellent transparency and color stability suitable for LED encapsulation.
MAX DIAMOND CLEAR A/B 48 OUNCE KIT
CRYSTAL CLEAR LED BULB ENCAPSULANT
Continuous Salt Water Immersion LED Dock Marker Lights
EPOXY RESIN MIXING AND USAGE APPLICATIONS
Please view the following video for the proper mixing of epoxy resins.
It demonstrates the proper technique of mixing any type of epoxy resin.
Best Epoxy Resin Mixing Procedure
Avoid Tacky Spots & Less Air Bubble
Improve Cure Performance
DON'T FORGET OUR EPOXY MIXING KIT
Click The Link To Add To Order https://www.ebay.com/itm/222623932456
EVERYTHING YOU NEED TO MEASURE, MIX, DISPENSE OR APPLY
1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams
4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups
4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix Cups
One Size Fits All Powder-Free Latex Gloves
2 Each Graduated Syringes
Wooden Stir Sticks
Assorted Size Foam Brush
PLEASE CHECK OUT OTHER AVAILABLE RESIN SYSTEMS AT OUR eBay STORE
IMPORTANT NOTICE
Your purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product.
The user should thoroughly test any proposed use of this product and independently conclude the satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval.
The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.
There is no warranty of merchantability for fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.