Stock Photo
See pictures for an example of what you will receive.
PLEASE NOTE: You will receive ONE (1) of the remotes pictured - all have the same circuit boards and will program the same
Logo will vary: May be blank, DEI, Hornet, Sidewinder, Python, Rattler, Your Valet, or Viper - all are produced by Directed Electronics and will program the same.
One (1)
Aftermarket Security Installed System remote keyless entry fob alarm controller
Transmitter control clicker keyfob controller replacement
DEI – Directed Electronics – VIPER- Python – Auto-Mate
– Rattler – SideWinder – Hornet – Merlin – Avital - Ungo
|
FCC ID#: EZSDEI471 Alternate Spelling: EZSDE1471 LED LIGHT: Green Buttons: 2; I,II Frequency: 433-434 MHz Battery: 1; GP23A See Item Specifications for more details
|
||||||||||||
|
Compatible With the following Aftermarket installed security systems:
|
|
Programming Instructions: The vehicle’s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle’s security system or to change button assignments if desired.
In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain's Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere).
The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit.
1) Open a door and make sure the dome light is on.
2) Turn the ignition on to the RUN position or you may also start car.
3) Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch.
4) You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release.
5) If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter.
6) Once the code(s) are learned, the Valet/Program push button can be released.
7) Programming mode will be exited if one of the following actions occurs: a. Ignition key is turned to the OFF position b. Valet/Program switch is pressed too many times. c. More than 15 seconds elapses between programming steps.
The horn will emit one long chirp when programming mode has been exited. |
How to find out if this remote is compatible with your Vehicles’ installed RKE System
If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.
1. Check the back of your current or old keyless remote to match FCC ID /Part #’s.
2. Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need.
Your vehicle will be installed with one of the following keyless entry systems:
a. Standard Keyless Remote Packages: Installed at time of manufacture.
b. Optional Keyless Remote Packages: Installed by a dealer.
c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop.
d. No remote keyless entry system at all.
The
above information can change which remote you need
for your installed remote keyless system.