MXL-RX62H-X-G V3.0 5 Channel Micro All-in-one Receiver Built-in 5A 1S Brushed ESC The Crossover-rx MXL-RX62H series receivers are a micro sized 5 channel all-in-one receiver with built-in 5A 1S brushed ESC and two linear servos. It features 2 independent micro JST-SH 1.00mm servo ports, and a set of solder pads to connect an external ESC. All of the Crossover-rx receivers feature a unique auto-binding system that is very user friendly. These are compatible with many readily available rotary and linear digital servos with micro JST-SH 1.00mm pitch connectors. There are also some protocols available with Telemetry back to the transmitter. 1) Size: 24.25x22.0x7.9mm (not including antenna) 2) Weight: 3.68g (including power cable) 3) Working voltage: 3.0~5.0V 4) Power cable approx. 90mm with Molex 1.25mm pitch ultra micro 2P plug which fits many 1s lipo batteries, JST-PH 2.0mm also available. 5) Built-in 5A/1S brushed ESC (Use of onboard ESC is optional, will support external brushless ESC) 6) You don't have to use the onboard ESC, you can direct solder an ESC into the throttle port, or reassign one of the servo output ports to the throttle function. 7) Very easy Auto binding program, Many available protocols: Spektrum DSMX DSM2, Futaba SFHSS, FRSKY-D8, FRSKY-D16, Flysky AFHDS-2A, and HOTT coming soon. 8) TELEM function: battery voltage, receiver voltage, signal strength, unit temperature 9) Servo connectors: Micro JST-SH 1.00mm pitch

Compatible servos https://www.ebay.com/itm/224392442967 Auto binding: The receiver will enter the binding mode automatically after power is applied and it doesn’t receive a transmitter signal for 15 seconds. This is indicated by the slow flashing blue LED light changing to a rapid flash. The receiver is now in the binding mode, complete the binding operation according to your transmitter’s binding instructions. Throttle range: Throttle range calibration is automatic. You may need to lower your throttle trim all of the way down for the ESC to sense zero throttle. TELEM function: The TELEM function monitors battery voltage, receiver working voltage, signal strength, as well as working temperature in real time. NOTE: The effective control range of the TELEM function depends on the transmitter, it is quite often that the working range of the receiver is far more than TELEM function effective range.

SR3X is a 3 axis flight stabilization system specially for fixed wing model airplanes. The SR3X is controllable from the transmitter and has three working modes: off, sensitivity-1, and sensitivity-2. The modes are indicated on the receiver by a blue LED; blue LED is off (stabilization is off), blue LED on steady (sense.-1), blue LED flashing (sense.-2). The default is for the mode selection to occur on channel 5. If your transmitter's CH5 switch is only a two position switch, you will have to allocate CH5 to a three position switch to use all three settings. Using the Crossover-RX USB Configuration Tool, you can select many additional options for the initial setup including horizontal or vertical mounting, differential thrust, aircraft configuration (flying wing, v-tail, etc.), and also mode selection channel. Also adjustable from the USB Configuration tool is the sensitivity of the SR3X stabilization in all modes and all axis, and even channel assignments.

Default axis - (all outputs are also reversible)

X axis = roll - outputs to the aileron channel

Y axis = pitch - outputs to the elevator channel

Z axis = yaw - outputs to the rudder channel

Default sensitivity-

Off 0%

Sense-1 45%

Sense-2 65%

Supported aircraft types-

Normal - Normal layout aircraft

Single Power Wing- Normal

Single Power Wing- Reverse

Dual Power Wing- Normal

Dual Power Wing- Reverse

V-Tail- Normal

V-Tail- Reverse

Supported mounting orientations-

Horizontal - the plane of the circuit board is normal to the plane of the wing

Flank - the plane of the circuit board is vertical

Control Mode (which transmitter channel controls the SR3X)-

OFF

SR3X Sense-1 ( sets sense-1 as on all of the time, not changeable from the TX)

SR3X Sense-2 ( sets sense-2 as on all of the time, not changeable from the TX)

AUX1 (CH5) Default

AUX2 (CH6)

AUX3 (CH7)

AUX4 (CH8)

CrossOver-RX USB Configuration tool- The CrossOver-RX USB Configuration Tool PG-02 plugs into a standard PC USB port and into your receivers MBUS port using either a 3 or 4 wire MBUS cord depending on the model of your receiver. There is a small micro switch on the tool that's position needs to be in the "I" position for use with a 3 wire cord, and the "II" position for a 4-wire cord. The first step in connecting your receiver to a PC is to download the current software:

CrossOver-RX Tool download address: update.crossover-rx.com/mxo.zip

Unzip this file and install it on your PC. Open the software. Plug the MX-PG02 USB configuration tool into a USB port on the PC. Plug the cord into the MBUS port on your receiver, other ports will not work. The tool will not connect to a receiver that is under power or linked to a TX. Look for USB-SERIAL CH340 in the port description box and select it, then press the connect button. The tool should connect and your receivers info should pop up in the profile tab. Make sure to save any changes you make to the configuration, and use the disconnect button before unplugging the receiver.

*Supported OS: WIN7-WIN11 X64 You may need to download the VC Runtime to run this application.