FCC ID: HH8-AVENGER-TX

Interchangeable FCC IDS:

Part #: 75

Frequency: 318 MHz

LED color: Blue  

2 buttons

BOARD: CS2BT-C

CHIP: HDR318M

Battery: (1) 23A

Compatible with the following systems:

Programming Instructions:

SECTION 3: SYSTEM OPERATION

The MCS-100 is very sophisticated, but the operation is simple. Your two button RF transmitter is easy to use for arm,

disarm, personal protection, and programming the system for many custom functions.

3.1 Remote System Arm (On)

- Press and release RF transmitter button #1.

- One siren chirp sound and a light flash verify the operation.

- If you hear four chirp sounds, the MCS-100 has detected a faulty sensor.

3.2 Remote System Disarm (Off)

- Press and release RF transmitter button #1.

- Two siren chirps and two light flashes verity this operation.

Note:

If you hear three chirp sounds, the system has been triggered and the alarm was activated while you were away from the vehicle. Please refer to following chart. This diagnostic report will turn off when ignition switch is turned on.

Diagnostic Report

Shock Sensor – 3 chirps (audible) – double flashes (visual LED)

Optional Input Trigger (Mercury Switch, Microwave & etc) – 3 chirps (audible) – Rapid flashes (visual LED)

3.3 Personal Protection Alarm (EMERGENCY PANIC)

- Press and hold down RF transmitter button #1 for approximately three seconds.

- Personal Panic alarm is activated and siren sounds and lights flash for one (1) minute.

- Press and release any RF transmitter button to cancel the panic alarm.

3.4 Motorcyle Finder Mode

- Press and hold down RF transmitter button #3 (#1+#2) for approximately three seconds.

- Lights flash for one (1) minute.

- Press and release any RF transmitter button to cancel the Motorcycle finder mode.

SECTION 4: PROGRAMMABLE FEATURES

Programming Function

Code Program Method 1

Power On. Within 3 seconds, press button #1 of new

transmitter. Press button #1 of 2^nd transmitter and then press button of 3^rd transmitter.

– 1 chirp – 1 Light

Code Program Method 2

(4.1) Turn Ignition On/Off 5 times. Press button #1 of new

transmitter. Press button #1 of 2^nd transmitter and then press button #1 of 3^rd transmitter.

 – 1 chirp – 1 Light

Permanent Siren Chirp Disable/ Permanent Siren Chirp Enable (4.2)

Turn Ignition on. Press button #2 for 5 seconds

– None & then 2 chirps – 1 Light & then 2 Lights

One Time Soft Chirp (4.3)

Press #2 before other function buttons.

Emergency Disarm (4.4)

Turn Ignition On/Off 4 times. Alarm will disarm.

– 2 chirp – 2 Light

Passive Mode

Active Mode (4.5)

Turn Ignition on. Press button #3 (#3 = #1 + #2) for 5

seconds.

– 1  & then 2 chirps – 1 Light & then 2 Lights

4.1 Permanent Reprogrammable Factory Code (Code Pre-Programmed By Factory)

When the Dealer installs the unit he programs your unique code which is in permanent memory. Any Authorized Dealer can add a new or an additional pre-coded transmitter and delete an existing code from memory.

To program a new code:

-        Turn the ignition key on and off five (5) times.

-        CODE CHANGE MODE is confirmed with one chirp sound and one parking light flash

-        Within 3 seconds, PRESS BUTTON #1. One chirp and one parking light flash will confirm the acceptance of new code. This operation will erase all previous codes.

-        Within 3 seconds, PRESS BUTTON #1 of 2^nd transmitter. One chirp and one parking light flash will confirm the acceptance of second code.

-        Within 3 seconds, PRESS BUTTON #1 of 3^rd transmitter. Once chirp and one parking light flash will confirm the acceptance of third code.

-        Code program will exit when 3 seconds is passed, when ignition is turned off or when all three codes are programmed

Note: Module will accept three different transmitters.