ODROID-H3 / H3+

ODROID-H3 and H3+ have the same form factor and similar power efficiency as their predecessor, the ODROID-H2+. However, the H3 and H3+ are more powerful, offering higher performance. You’ll need to supply your own memory and storage (check the recommended accessories on this page) — but since the ODROID-H3 family uses the same components commonly found in modern laptops, you should have no trouble finding compatible hardware to fill out your SBC. ONLY NVMe M.2 SSD ARE COMPATIBLE: PCIe NVMe M.2 SSD Both models of ODROID-H3 feature two SO-DIMM slots for memory, two SATA ports and one M.2 NVMe slot for storage, two 2.5 GbE ports, two USB 3.0 ports, two USB 2.0 ports and more! ODROID-H3: Intel quad-core Jasper Lake N5105 processor ODROID-H3: Intel quad-core Jasper Lake N6005 processor Additional items required to operate - see "REQUIRED ITEMS" section below. KEY FEATURES SoC: H3: Intel Jasper Lake N5105 quad-core processor, base clock of 2.0GHz and boost up to 2.9 GHz H3+: Intel Jasper Lake N6005 quad-core processor, base clock of 2.0GHz and boost up to 3.3 GHz GPU: H3: Intel UHD Graphics 24 EUs Turbo 800MHz H3+: Intel UHD Graphics 32 EUs Turbo 900MHz System Memory – Dual-channel Memory DDR4 PC4-23400 (2933MT/s) supporting up to 64GB RAM in total Storage – M.2 PCIe 3.0 x4 slot for one NVMe storage, 2x SATA 3.0 ports, eMMC flash support Video Output HDMI 2.0 up to 4K (4096×2160) @ 60 Hz DisplayPort 1.2 up to 4K (4096×2160) @ 60 Hz Audio – HDMI, audio jacks for HP, MIC. and S/PDIF Connectivity – Dual 2.5 Gigabit Ethernet (RJ45) Expansion – 24-pin header with I2C, UART (3.3V), USB2.0 and HDMI CEC signals SSE4.2 accelerator (SMM, FPU, NX, MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, AES) A configurable Unlimited Performance mode allowing the CPU to run in sustained turbo boost mode Misc – RTC battery (Included) Power Supply – 14V to 20V DC power input Dimensions – 110x110x43mm Weight – About 320 grams with heatsink, two DRAM modules, and M.2 NVMe SSD. REQUIRED ITEMS (NOT INCLUDED) No power supply included - 15VDC/4A power supply required No RAM pre-installed - DDR4 SODIMM DDR3/DDR5 is not supported No eMMC Module or SSD included M.2 SATA SSD is not supported (only NVMe SSD) No case included No HDMI cable included - needed to connect to a display device. Recommend HDMI2.0 cable to support 4K output SPECIFICATIONS Processor: Intel Celeron N5105(H3+: N6005) Processor (10nm, Quad-Core, TDP 10W) H3(N5105) : up to 2.9GhzH3+(N6005) : up to 3.3Ghz 4MB L2 Cache Intel UHD Graphics (24/32 EU up to 900MHz) Memory: 2 x DDR4 1.2V SO-DIMM slots, Dual Channel, up to 2933 MT/s (DDR4-PC23400) Max memory capacity 64GB DDR3/DDR5 are not supported Storage: 1 x eMMC connector (bootable and selectable on BIOS) 2 x SATA3 6Gbps 1 x M.2 slot (PCIe 3.0 x 4, supports NGFF-2280 cards) M.2 SATA SSD is not supported Networking: 2 x GbE LAN ports (RJ45, supports 10/100/1000/2500 Mbps) Realtek RTL8125B Supports Wake-On-Lan LED indicators (Green: Link, Amber: Traffic) Video: 1 x DisplayPort 1.2 (up to 4K@60Hz) 1 x HDMI 2.0 (up to 4K@60Hz) Dual simultaneous display support Audio: 1 x Audio out (3.5mm jack) 1 x Audio in (3.5mm jack) 1 x SPDIF out (ALC1200, HDA codec) * HDMI & DP have audio output too. External I/O: 2 x USB 3.0 Host ports 2 x USB 2.0 Host ports 1 x Peripheral Expansion Header (24-pin, 2.54mm pitch) 1 x DC 5V, 1 x DC 3.3V, 5 x GND 1 x UART (TXD/RXD/RTS/CTS) 2 x I2C (SCL/SDA) 1 x External Power Button HDMI CEC, 5VA+ Three USB 2.0 ports All 3.3V I/O signal level Other Features: Passive Heatsink BIOS Backup Battery Maintains system time and BIOS settings Power Button Reset Button System LEDS Indicators: Red (PWR) – Solid light when DC power is supplied Blue (left, SLEEP) – turns off only when the system enters into suspend mode Blue (right, PMIC) – turns on only when the major power rails are working Amber (SATA) – Flashes when SATA data transfers Green (NVMe) – Flashes when NVMe data transfers Active Cooling Fan Connector (12V 4-pin, PWM input + TACHO output) Active Cooling Fan is optional Connector (4-pin, 2.54mm pitch) Power: DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm DC 14V ~ 20V (up to 60W) DC 15V/4A power adapter is recommended if you don’t use two 3.5“ HDDs DC 19V/7A power adapter is recommended if you two 3.5” HDDs together Power consumption: IDLE : ≃1..9W CPU Stress : ≃15W CPU+GPU Stress : ≃18W Power-off : ≃0.25W Suspend : ≃0.6W Form Factor: 110mm x 110mm x 47mm Approx. A. CPU (Intel Celeron N5105) B. 2 x DDR4 SO-DIMM slots (Dual channel memory support) C. 1 x M.2 PCI Express Module Socket (NGFF-2280) D. 1 x eMMC (Embedded Multimedia-Card) Socket E. 2 x SATA Power Connectors (2.5mm pitch, JST-XH compatible connector) F. 2 x SATA3 6.0 Gb/s Data Connectors G. 1 x DC Power Jack H. 2 x USB 3.0 I. 2 x USB 2.0 J. 1 x HDMI 2.0 K. 1 x DisplayPort 1.2 L. 2 x RJ45 Ethernet Ports (10/100/1000/2500) M. 5 x System LED Indicators N. 1 x Peripheral Expansion Header (24-pin) O. 1 x Power Switch P. 1 x Reset Switch Q. 1 x Backup Battery Connector (2-pin) R. 1 x Active Cooling Fan Connector (4-pin) S. 1 x Audio out, 1 x Audio in, 1 x SPDIF out LINKS Installation - https://wiki.odroid.com/odroid-h3/start#installation WiKi - https://wiki.odroid.com/odroid-h3/start Introduction - https://dn.odroid.com/ODROID-H2/H3_pics/H3_H3+_Introduction.pdf VIDEOS

ODROID-H3 / H3+

ONLY NVMe M.2 SSD ARE COMPATIBLE: PCIe NVMe M.2 SSD

Both models of ODROID-H3 feature two SO-DIMM slots for memory, two SATA ports and one M.2 NVMe slot for storage, two 2.5 GbE ports, two USB 3.0 ports, two USB 2.0 ports and more!

ODROID-H3: Intel quad-core Jasper Lake N5105 processor
ODROID-H3: Intel quad-core Jasper Lake N6005 processor

Additional items required to operate - see "REQUIRED ITEMS" section below.

KEY FEATURES

SoC:

H3: Intel Jasper Lake N5105 quad-core processor, base clock of 2.0GHz and boost up to 2.9 GHz
H3+: Intel Jasper Lake N6005 quad-core processor, base clock of 2.0GHz and boost up to 3.3 GHz

GPU:

H3: Intel UHD Graphics 24 EUs Turbo 800MHz
H3+: Intel UHD Graphics 32 EUs Turbo 900MHz

System Memory – Dual-channel Memory DDR4 PC4-23400 (2933MT/s) supporting up to 64GB RAM in total
Storage – M.2 PCIe 3.0 x4 slot for one NVMe storage, 2x SATA 3.0 ports, eMMC flash support
Video Output
- HDMI 2.0 up to 4K (4096×2160) @ 60 Hz
- DisplayPort 1.2 up to 4K (4096×2160) @ 60 Hz
Audio – HDMI, audio jacks for HP, MIC. and S/PDIF
Connectivity – Dual 2.5 Gigabit Ethernet (RJ45)
Expansion – 24-pin header with I2C, UART (3.3V), USB2.0 and HDMI CEC signals
SSE4.2 accelerator (SMM, FPU, NX, MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, AES)
A configurable Unlimited Performance mode allowing the CPU to run in sustained turbo boost mode
Misc – RTC battery (Included)
Power Supply – 14V to 20V DC power input
Dimensions – 110x110x43mm
Weight – About 320 grams with heatsink, two DRAM modules, and M.2 NVMe SSD.