FAST and SAFE shipping from our office in San Jose, California with shipping time and tracking # Two notices will be sent to you by email: 1. Payment received. 2. Order status: shipping time and tracking #. |
Features: 1) 2 channels are respectively controlled by independent knobs 2) 100MHZ or 150MHZ analog channel bandwidth 3) Sampling rate up to 1GSa/s 4) 8M memory depth 5) Vertical range 2mV/div ~ 10V/div 6) Built-in 1CH 25MHz waveform generator, support arbitrary waveform burst output, support modulation waveform output (only for DSO2D10, DSO2D15) 7) Vertical resolution: 8bit 8) Trigger: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC 9) BUS decode and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN 10) Can save multiple data formats, such as settings, waveforms, reference waveforms, CSV, pictures 11) A 3-digit digital voltage meter and a 6-digit hardware frequency indicator 12) 32 kinds of automatic measurements with statistics, real-time statistics of maximum, minimum, standard deviation and etc. 13) 2 sets of digital voltmeters 14) Support threshold testing, free measurements within the screen 15) Abundant SCPI remote command control 16) USB Host/Device Model Selection Guide Model | Channel | Bandwidth | Sample Rate | Memory Depth | AFG (Arbitrary Function Generator) | DS02C10 | 2Ch | 100MHz | 1GSa/s | 8MSamples | N/A | DS02C15 | 2Ch | 150MHz | 1GSa/s | 8MSamples | N/A | DS02D10 | 2Ch + 1Ch | 100MHz | 1GSa/s | 8MSamples | 1Ch | DS02D15 | 2Ch + 1Ch | 150MHz | 1GSa/s | 8MSamples | 1Ch |
Specification Model | DSO2D15 | DSO2D10 | DSO2D15 | DSO2C10 | Bandwidth | 150MHz | 100MHz | 150MHz | 100MHz | Oscilloscope Channels | 2Ch | 2Ch | 2Ch | 2Ch | Arbitrary Function Generator | 1Ch | 1Ch | | | Horizontal | SEC/DIV Range | 2ns/div to 100s/div, in a 1, 2, 5 sequence | Delta Time Measurement Accuracy (Full Bandwidth) | Single, sampling mode ± (1 sample interval + 100ppm × reading + 0.6ns) | >16 times above average ± (1 sample interval + 100ppm × reading + 0.4ns) | Sample interval = s/div ÷ 200 | Vertical | A/D Converter | 8-bit resolution, each channel sampled simultaneously | VOLTS/DIV Range | 2mV/div to 10V/div at input BNC | Offset Range | 2mV/div ~ 200mV/div, ±1V 500mV/div ~ 10V/div, ±50V | Selectable Analog Bandwidth Limit (Typical) | 20MHz | Low Frequency Response (−3db) | ≤10Hz at BNC | Rising Time at BNC (Typical) | DSO2C10 | DSO2C15 | DSO2D10 | DSO2D15 | ≤3.5ns | ≤2.4ns | ≤3.5ns | ≤2.4ns | DC Gain Accuracy | ±3% for Normal or Average acquisition mode, 10V/div to 10mV/div | ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div | Vertical Offset Accuracy | ±0.1div±2mV±1% Offset | Mathematical Operation | +, −, ×, /, FFT | FFT | Window Function Types: Rectangle, Hanning, Hamming, Blackman, Bartlett and Flat Top | Voltage Measurement Repeatability, Average Acquisition Mode | Under the same setting and environment, ≥16 waveforms are sampled, ΔV of any two averages: ± (3% × value + 0.05 div) | Note: Bandwidth reduced to 6MHz when using a 1X probe | Acquisition | Sample Rate Range | 1GSa/s (single channel), 500MSa/s (dual channels) | Acquisition Modes | Normal, Peak, Average & High Resolution | Waveform Interpolation | (sin x)/x | Acquisition Rate (Typical) | Up to 2000 waveform per second per channel (Normal acquisition mode, no measurement) | Minimum Detection Pulse Width | 2ns | Single Sequence | Acquisition Mode | Acquisition Stop Time | Normal, Peak Detect | Upon single acquisition on all channels simultaneously | Average | After N acquisitions on all channels simultaneously, N can be set to 4, 8, 16, 32, 64 or 128 | Memory Depth | Maximum 8M for single channel (4K, 40K, 400K, 4M, 8M optional) Maximum 4M for dual channels (4K, 40K, 400K, 4M optional) | Trigger | Trigger Type | Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Delay, UART, LIN, CAN, SPI, lIC | Trigger Level Range | ±5 divisions from the center of the screen | Mode | Auto, Normal, Single | Level | CH1 ~ CH2 | ±5 divisions from the center of screen | EXT | 0~3.3V [CMOS] | Holdoff Range | 20ns ~ 10s | Trigger Level Accuracy | CH1~CH2 | 0.2 div × volts/div within ±4 divisions from the center of the screen | EXT | ± (Set value × 6% + 40mV) | Trigger Sensitivity | ±0.2div | Edge Trigger | Slope | Rising, Falling, Rising & Faling | Source | CH1 ~ CH2, Line, External | Pulse Trigger | Polarity | Positive, Negative | Condition | <,>,!=,= | Source | CH1 ~ CH2 | Pulse Width Range | 8ns ~ 10s | Accuracy | 8ns | Video Trigger | Signal standard | NTSC, PAL | Signal source | CH1 ~ CH2 | Synchronization | ScanLine, LinrNum, OddField, EvenField and AllField | Slope Trigger | Slope | Nse, Fall | Condition | <, >, !=, = | Source | CH1 ~ CH2 | Time Range | 8ns ~ 10s | Accuracy | 8ns | Overtime Trigger | Source | CH1 ~ CH2, | Polarity | Positive, Negative | Time range | 8ns ~ 10s | Accuracy | 8ns | Window Trigger | Source | CH1 ~ CH2 | Pattern Trigger | Pattern | 0: low level; 1: high level; X: ignore | Level | CH1 ~ CH2 | Interval Trigger | Slope | Rising, Falling | Condition | <, >, !=, = | Signal Source | CH1 ~ CH2 | Time Range | 8ns ~ 10s | Accuracy | 8ns | Under Amp Trigger | Polarity | Positive, Negative | Condition | <, >, !=, = | Source | CH1 ~ CH2 | Time Range | 8ns ~ 10s | Accuracy | 8ns | UART Trigger | Condition | Start, Stop, Data, Parity Error, COM Error | Source | CH1 ~ CH2 | Data Format | Hex | Condition | <, >, !=, = | Data Length | 1 byte | Data Bits Width | 5 bit, 6 bit, 7 bit, 8 bit | Parity Check | None, Odd, Even | Idle Level | High, Low | Baud Rate (Selectable) | 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s | Baud Rate (Custom) | 300bit/s ~ 334000bit/s | LIN Trigger | Condition | Interval Field, Sync Field, Id field, Sync Id Error, Identifier, Id and Data | Source | CH1 ~ CH2 | Data Format | Hex | Baud Rate (Selectable) | 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s | Baud Rate (Custom) | 300bit/s ~ 334000bit/s | CAN Trigger | Condition | Start Bit, Remote Frame, Data Frame Id, Frame Id, Data Frame Id A, Error Frame, All Error, Ack Error, Overload Frame | Source | CH1 ~ CH2 | Data format | Hex | Baud Rate (Selectable) | 10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000,1000000 | Baud Rate (Custom) | 5kbit/s ~ 1Mbit/s | SPI Trigger | Source (SDA/SCL) | CH1 ~ CH2 | Data Format | Hex | Data Length | 4, 8, 16, 24, 32 | IIC Trigger | Source (SDA/SCL) | CH1~CH2 | Data Format | Hex | Data Index | 0~3 | Condition | Start Bit, Stop Bit, No Ack, Address, Restart, Address and Data | Input | Number of Channels | 2 analog channels | Input Coupling | DC, AC or GND | Input Impedance, DC Coupled | 20pF ± 3pF, 1MΩ ± 2% | Probe Attenuation | 1X, 10X | Supported Probe Attenuation Factors | 1X, 10X, 100X, 1000X | Overvoltage Category | 300V CAT II | Maximum Input Voltage | 300VRMS (10X) | Isolation Between Channels | >40dB | Delay Deviation Between Channels | <500ps | Measurements | Cursors | Voltage difference between cursors: ΔV | Time difference between cursors: ΔT | Reciprocal of ΔT in Hertz (1/ΔT) | Automatic Measurements | PkPk, Frequency, Average, Max, Min, Period, Vtop, Vmid, Vbase, Vamp, RMS, R-Overshoot, PeriodRms, F-Preshoot, PeriodRms, PeriodAvg, RiseTime, FallTime, +Width, −Width, +Duty, −Duty, FRR, FFF, F−Overshoot, R−preshoot, BWidth, FRF, FFR, LRR, LRF, LFR and LFF | DVM | Data source | CH1, CH2 | Measurement type | DC RMS, AC RMS, DC | Frequency meter | hardware 6 bits frequency meter | Math Operation | Source | CH1~CH2 | Operator | +, −, x, /, FFT | FFT | Point | 1024 | Window | Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop | Display | Show only or show all | Vertical scale | dB, VRms | Storage | Save/Recall (Non-volatile) | 9 types of files can be saved and recalled internally, including settings, waveforms, and references | Save to External Memory | CSV file, BMP picture (24 bit) | Arbitrary Waveform Generator | Channel | 1 | Standard Waveforms | Sine, Square, Ramp, Exponential, Noise, DC | Sin | Frequency range | 0.1Hz ~ 25MHz | Square / Pulse | Frequency range | 0.1Hz ~ 10MHz | Duty | 1% ~ 99% | Triangular Wave | Frequency range | 0.1Hz ~ 1MHz | Ramp | Frequency range | 0.1Hz ~ 1MHz | Symmetry | 0% ~ 100% | Exponential | Frequency range | 0.1Hz ~ 5MHz | Noise | Bandwidth | >25MHz | DC offset | Range | ±3.5V, high impedance | ±1.75V, 50Ω | Resolution | 100µV or 3 bits, take the greater one | Accuracy | 2% (1kHz) | Arbitrary waveform | Frequency Range | 1µHz ~ 25MHz | Wave length | 4096 | Support PC download and external memory recall | Output impedance | 50 Ω + 1%, high impedance | Amplitude | Output range | 10mV ~ 7Vp-p (high impedance ) 5mV ~ 3.5Vp-p (50Ω) | Amplitude accuracy | ±3dB | | Waveform Depth | 4KSa | Frequency Resolution | 1uHz | Frequency Accuracy | <10KHz,100ppm >10KHz,50ppm | Modulation | FM | Modulation waveform | Sine, square, ramp | Modulation frequency | 1Hz ~ 50kHz | Modulation deviation | 0.1Hz ~ Carrier frequency | AM | Modulation waveform | Sine, square, ramp | Modulation frequency | 1Hz ~ 50KHz | Modulation depth | 0% ~ 120% | Burst | Types of | N Cycle, Infinite | Number of cycles | 1 ~ 1024 | Trigger source | Manual | Trigger Input Signal Source | Level | MOS | Probe Compensator Output | Output Voltage (Typical) | 5V | Frequency (Typical) | 1kHz ± 1% | Display | Display Type | 7 inchs TFT (diagonal liquid crystal) | Display Resolution | 800 (horizontal) × 480 (vertical) pixels | Display Type | Point, vector | Waveform Brightness | Adjustable | Grid Type | Adjustable | Grid Brightness | Adjustable | Screen Brightness | Adjustable | Display Colour | 16 million colours (24 bits true colour) | Persistence time | Minimum, 1s, 5s, 10s, 30s, infinite | Interface | Standard Interface | USB Host, USB Device | Power Supply | Supply Voltage | 100 ~ 120VACRMS (±10%), 45Hz to 440Hz, CAT II | 120 ~ 240VACRMS (±10%), 45Hz to 66Hz, CAT II | Power Consumption | <15W | Fuse | T2A 250VAC 4*8 | Environmental | Operating Temperature | 0 to 50 °C (32 to 122 °F) | Storage Temperature | −40 to +71 °C (−40 to 159.8 °F) | Humidity | ≤ +104°F (≤ +40°C): ≤90% relative humidity | Cooling Method | 106°F ~ 122°F (+41°C ~50°C): ≤60% relative humidity | Altitude | Operating and Nonoperating | 3,000m (10,000 feet) | Random Vibration | 0.31gRMS from 50Hz to 500Hz, 10 minutes on each axis | Nonoperating | 2.46gRMS from 5Hz to 500Hz, 10 minutes on each axis | Mechanical Shock | Operating | 50g, 11ms, half sine | Mechanical | Dimension | 318 × 110 × 150mm (L × W × H) | Weight | 1900g |
I. PAYMENT We accept PayPal and all major credit cards, including Visa, Master Card,, American Express, Discover, etc. II. SHIPPING We ship by USPS, UPS or FedEx whichever costs the least or per customers' requests. III. RETURN/EXCHANGE Return Policy: 1.There is a 5% or 15% restocking fee for unopened or opened items respectively. 2. Items with marks or alternated cannot be returned because we cannot resell them. 3. Items should be returned with original packaging materials and accessories. 4. Please put a note inside the package indicating your eBay user name, purchase date, and the reasons for returning. 5. Buyers pay for shipping the items back and the original shipping fee to the buyer will be deducted from the refund. 6.14 days full refund return with original packaging and no damage on the product. We only pay for return shipping if our product is defective. IV.CUSTOMER SERVICE We have full time staff answering phone calls for technical and sales related question from 8am to 5pm AEST and reply eBay or email messages within 1 day. Please feel free to send us messages, we are all ears. About this instrument: our company, Analog Technologies, Inc., has been designing and developing analog electronic products for 25 years. This item has been used and highly recommended by our electrical engineers. Its user manual can be found online or downloaded from our company's website. That's why we are selling it here with the confidence that you will like it as well. Only if you are happy with our products and services then we will be happy. About us: Our company, Analog Technologies, Inc., was started as an R&D firm in January 7, 1997, in Novi, Michigan, a small town 25 miles from Detroit. After 26 years hard working, we have established branches in San Jose, California, USA; Sydney, Australia; and Anshan, Liaoning, P.R. China. We have 3 departments: R&D, Production and Trading. The products sold on eBay are either produced by our own Production Department or our sub-contractor companies. If you have any questions and/or suggestions, please contact us. Our goal is to make our customers happy and grow our company to a bigger one.
|