3/5/7mtr 12v Ready Made Leads Split Charge Relay Kit with 12V 140amp Intelligent Voltage Sense Relay with Digital Voltmeter Display
Applications:
This kits is suitable for safely charging up to 220AH Leisure batteries.
This kits is suitable for Camper Vans, Motor homes, 4x4s, Day Vans, Mobile workshops,Cars or Boats.
Descriptions
OUHOUG® Digital Voltmeter Display Voltage sense systems are especially suited for modern vehicles with canbus controlled wiring as this type of kit does not need an ignition feed or any additional wiring and are very simple kit to install, all you need to do is to connect your starter battery to your leisure battery(s) by using the kit supplied, with very easy to understand fitting instructions and a wiring diagram.
The voltage sense relay simply detects the rise in voltage from you vehicles charging system to allow you to charge your leisure battery(s) while your engine is running. When your engine is switched off, the relay will isolate your leisure battery(s) from your main starter battery. So it does not drain your main starter battery and you will always be able to start your vehicle.
Highlights of OUHOUG® Digital Voltmeter Display Voltage Sensitive Relay compare to old version VSR without Digital Voltmeter Display:
- Digital Voltmeter Display for sensing battery voltage
- Emergency Switch button for auto or manual charging mode
- Hardware inside VSR fully upgraded with more reliable and higher quality components
3m kit
The kit includes everything you need for setup dual battery charging system :
- 12v 140amp Digital Voltmeter Display Smart Voltage Senstive Relay
- 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder lead
- 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder lead
- 1 x 2 metre 70amp Relay to fuse holder READY MADE Lead
- 1 metre 70amp of READY MADE Black Earth Lead
- 1 Pair 8mm Post Type Battery Terminals
- 2 x MTA MIDI Fuse holders
- 4 x 60A MTA MIDI Fuses including 2 spares.
- Red&Black Heat shrink to protect all the connections.
- 10 x Cable ties
- 10 x adhesive cable tie fixings base to keep everything tidy.
- 15 x fixing screws
- Easy to understand Fitting Instructions + after sales support if required
5m kit Package Includes: (You will be supplied with everything you need to fit this kit)
- 12v 140amp Digital Voltmeter Display Smart Voltage Senstive Relay
- 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder lead
- 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder lead
- 1 x 4 metre 70amp Relay to fuse holder READY MADE Lead
- 1 metre 70amp of READY MADE Black Earth Lead
- 1 Pair 8mm Post Type Battery Terminals
- 2 x MTA MIDI Fuse holders
- 4 x 60A MTA MIDI Fuses including 2 spares.
- Red&Black Heat shrink to protect all the connections.
- 10 x Cable ties
- 10 x adhesive cable tie fixings base to keep everything tidy.
- 15 x fixing screws
- Easy to understand Fitting Instructions + after sales support if required
7m kit The kit includes everything you need for setup dual battery charging system :
- 12v 140amp Digital Voltmeter Display Smart Voltage Senstive Relay
- 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder lead
- 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder lead
- 1 x 6 metre 70amp Relay to fuse holder READY MADE Lead
- 1 metre 70amp of READY MADE Black Earth Lead
- 1 Pair 8mm Post Type Battery Terminals
- 2 x MTA MIDI Fuse holders
- 4 x 60A MTA MIDI Fuses including 2 spares.
- Red&Black Heat shrink to protect all the connections.
- 10 x Cable ties
- 10 x adhesive cable tie fixings base to keep everything tidy.
- 15 x fixing screws
- Easy to understand Fitting Instructions + after sales support if required
**Please note**: The 3/5/7 mtrs of Red cable supplied in this kit are made up of the 4 separate leads (such as 3mtr: it was separated to 2M+2*0.25M+0.5M) which is pre-assembled with terminals as described above. choose the correct meter for yourself in case short of wire.