Stock Photo

COMPLETELY faded button graphics / some case scuffs / no cracks

See pictures for an example of what you will receive

 

 

One (1)

Aftermarket remote keyless entry fob alarm

Transmitter control clicker keyfob controller replacement

 

Functions at 100% Tested & Guaranteed

 

Clifford

 

FCC ID: CZ57RRKC

 Interchangeable Part #s:

904065

904060

 Frequency: 433 – 434 MHz

 3 buttons

 Battery: (1) CR 2032

 

 

 

Compatible with the following systems:

 Ace 2000(G4)

 Arrow 3(G4)

Cyber 2(G4)

 GP500 Matrix 1

 Polaris4 (G4)

SP-300 / SP300

 

 

 Programming Instructions:

1. Get in your vehicle.

2. Turn the ignition on, or start the engine.

3. Enter your Valet code. Your Valet code will be something you’ve already created with your vehicle’s RKE system. If you have not created a Valet code, you should use the factory setting code as described in the user manual for your vehicle’s RKE system. After entering your Valet code you should press and hold the ✱button of the PlainView 2 Valet switch for about 4 seconds until you hear a siren chirp.

4.Select the feature column from the chart below:

Press and release the blank button of the PlainView 2 switch the same number of times as the column number you wish.

Pause.

You will hear the same number of chirps as the column number, audibly confirming your selection.

5.Select the feature row:

Press and release the ✱button the same number of times as the row number. You’ll will hear a chirp each time you press to help you count

Pause

. You will hear either one or two chirps:

Two chirps = ON, one chirp = OFF

(If there is a NOTE for the selected feature, perform the actions noted)

You may now select another feature or exit program mode

a. To select another feature in that same column, repeat step 5 within the next 5 seconds

(after 5 seconds, 3 chirps mean you are back to the “Feature Select” position).

b. To select a different feature column, go to step 4.

c. To exit program mode, turn the ignition off (you’ll hear 3 chirps and the LED will turn off). If driving, just wait 60 seconds and the system will automatically exit program mode.

If you make an error, just turn off the ignition and start again.

 

CHANNEL #

1 blank press

2 blank presses

 3 blank presses

1 * press

Add a new remote control

Note 1

Chirps: off/on

(1/2 chirps)

AutoArming off/on

2 * presses

Personalize Siren sounds

See your owner’s manual

NOT USED

Lock upon Auto

Arming: off/on

3 * presses

Personalize Siren sounds

See your owner’s manual

Remote Valet Mode

VIA button combo

(Trunk release & * off/on)

AutoArming entry

Delay: off/on

4 * presses

Siren duration 30/60/90 sec.

(1/2/3 chirps)

AutoStart*

both off/on/temp only/

battery only

(1/2/3/4 chirps)

Fact: off/on

5 * presses

AutoLock: off/on

NOT USED

NOT USED

6 * presses

AutoUnlock off/on

Clear all remotes

Note 2

NOT USED

7 * presses

Reset all features (except remote

and valet code) to factory settings

Set a new secret Valet Code

Note 3

NOT USED

Note 1: Press the unlock/lock button of the remote you’re programming. You’ll hear one chirp. Press the unlock/lock button again. You’ll hear two chirps to confirm that the remote has been added.

Note 2: You’ll hear two chirps to indicate all remotes have been cleared from memory. You must now add new/existing remotes with the “Add new remote control” feature.

Note 3: Immediately press the blank button, then enter your new code, wait for the two chirps, then turn off the ignition (you’ll hear 3 chirps to confirm program mode exit). You must now turn the ignition back to on and then re-enter your new code. If the LED flashes on, your new code has been accepted. If the LED does not light, the two codes did not match and the system has reverted to your previous code.