If you have any questions, please contact customer service first, do not open disputes easily, thank you!
Features
Compatible with For Xbox 360/Xbox One series/PS4/PS3/Switch controllers
Custom button layout to map up to 12 physical buttons to any logical button of JVS
Rapid Fire,enable rapid fire mode for each physical button
Persistent Configurations,store and restore up to 10 sets of button layouts
Rapid fire settings,speed,and other configurations
Firmware Updates,to fix bugs or improve compatibility
Dual joystick mode,when the For PS4 controller is connected to the 1P USB port
Press PS button to switch operation mode between normal mode and dual joystick mode
Mahjong mode,when connected to a USB keyboard that supports boot mode
Although almost all keyboards will support it,IONA will switch to Mahjong mode
User Guide
1.Connect USB Type C port for power supply
It does not require a data connection
Only a 5V power supply is required for the IONA
USB charger will be available
The PC USB port can also support the required power.
PC-based JVS system boards can have a port for this purpose
For example,the For exA-Arcadia has a hidden USB port
But if you want to use devices that require a lot of power
However,if you want to use devices that require a lot of power
The power supply from the PC via the USB bus may not be enough and the IONA will become unstable
2.Connecting the JVS port to the JVS system board
You can use a normal USB cable
3.Connect the USB gamepad at any time
Even when the JVS bus is active
You can also connect and disconnect
The LED starts blinking when the power is turned on
Once the address is assigned via the JVS bus,the LED lights up
If the IONA receives a reset signal via the JVS bus,it will start blinking again
Setting
Bus operation mode
At startup,the IONA operates in normal mode
Press the TEST and SERVICE buttons on the IONA board to change the operation mode
1.Normal mode(LED - blinking or illuminated,depending on JVS bus status)
Works as a JVS I/O handle with selected settings
2.Layout configuration mode(LED-fast blinking)
Push TEST and SERVICE together and it enters the layout configuration mode
You need to push them simultaneously for at least 0.5 seconds and up to 5 seconds
You do not need to put them completely together
For example keeping TEST pressed and clicking on SERVICE will work
In the key layout mode you will select the physical keys,coins,start,keys 1 to 10 in the following order
If multiple keys are pressed together,you can assign multiple physical keys to one key
You also do not need to push them at the exact time
When you press a button,IONA starts recording all pressed buttons
until all buttons are released,then assign them all to the target button
Continue this sequence until all 12 buttons are mapped
If you leave this mode before setting all,the remaining buttons will remain unassigned
If you do not configure any buttons
then IONA will not update the layout at all and move to the next mode
3.Burst configuration mode(LED-flashing)
You can press multiple physical buttons that enable rapid fire
Again,the timing should not be exact.You can try multiple times until you exit this mode
4.Speed configuration mode(LED-slow flashing)
You can select the burst speed with buttons 1-6
Buttons 1-6 are not physical buttons,but are mapped in a custom layout
Each button 1-6 is mapped to 30/20/15/12/10/8.5 fps
You can try at any time until you exit the mode
Faster if you press multiple buttons
If the release time is different,the latter is used
The settings selected above will be stored permanently
5.Restore factory settings(LED-flashing)
You can reset all settings and restore the default settings by pressing TEST and SERVICE at the same time outside of the normal mode
The LED flashes and then automatically returns to normal mode
6.Recall stored configuration(LED-off)
You can enter the mode to recall the stored configuration by pressing the SERVICE button outside of the normal mode
The factory settings are initially set to 1
You can recall another configuration again until you press SERVICE again to exit this mode
If the firmware version is earlier than 1.40,press SERVICE to return to normal mode
Otherwise,for version 1.40 and higher,pressing TEST will move to the analog layout configuration mode
7.Analog Layout Configuration Mode(LED-Fast Blinking)
You can select 6 inputs for the analog signal report
When you enter this mode,the analog input values will be remembered as base values
You can move analog rockers or triggers that are recognized as analog inputs
You may wish to move it to the right,down or to normal polarity
If you want to reverse it, you can move it to the opposite side
Once you stop moving the joystick or trigger and return it to its original position,the input will be recorded
You need to repeat the same steps 6 times for analog inputs 1 to 6
You can exit this mode by pressing TEST and skip the following assignments and use the previous settings
8.Option configuration mode(LED-blinking)
You can exit the setup mode by pressing TEST,but the options will be set via the P1 button when you exit the mode
The button numbers are logical according to your custom layout.The default setting is All Off
Package includes:
1*Handle adapter
Note:
Only the above package products are included
The product itself with the logo,I hope you do not mind