1: Low voltage version 12V~40V
2: Using synchronous rectification technology, small heat generation, small size and high efficiency
3: Adopt high-speed dedicated 32-bit main control chip with DSP
4: Fast response and accurate operation
5: Simple to use
2: Using synchronous rectification technology, small heat generation, small size and high efficiency
3: Adopt high-speed dedicated 32-bit main control chip with DSP
4: Fast response and accurate operation
5: Simple to use
Parameter:
Can drive 42 57 86 4-wire 8-wire two-phase stepper motor
Voltage input range: DC12-40V
32-bit dedicated high-speed DSP control chip
Current output range: 0.9-4.2A
Subdivision range: 4(800) -128 (25600)
Signal input amplitude: compatible with 3-24V
Can drive 42 57 86 4-wire 8-wire two-phase stepper motor
Voltage input range: DC12-40V
32-bit dedicated high-speed DSP control chip
Current output range: 0.9-4.2A
Subdivision range: 4(800) -128 (25600)
Signal input amplitude: compatible with 3-24V
Reminder: This driver adopts 8 independent MOS tubes with low internal resistance and has automatic half-current function. When the motor stops rotating and keeps (when there is no input step pulse for 0.5 seconds), the running current is automatically halved, so the calorific value is very small. It is not at all comparable to single-chip integration, such as the upgraded version of TB67S109S, which is the most used TB6600 on the market. Buyers are welcome to compare PK.
product description
DM542X is our company's dedicated high-speed 32-bit digital two-phase hybrid stepping motor driver with DSP control, suitable for phase current below 4.2A, 4-wire 6-wire 8-wire two-phase hybrid type with an outer diameter of 42 57 parts 86 stepper motor. Various subdivisions within 128 and various currents within 4.2A can be set, using advanced digital PWM current control technology, higher step accuracy, lower noise, much better than traditional chopping current control technology, using synchronous rectification automatic The half-flow technology has extremely low heat generation, the volume can be minimized, and the lack of phase and mis-phase overcurrent protection makes the product smarter and more reliable, and the drive runs more smoothly.
Application field:
It is suitable for automation equipment and instruments in various motion control fields, such as: industrial control equipment, 3D printing, laser processing, engraving, medical measurement, motor processing, textile and clothing, etc. In the field where users expect low noise, low vibration, small size, high performance, and high cost performance Preferred recommended products.
Regarding the current setting, it is not that the larger the current setting, the better. It is necessary to match the load according to the size of the motor, the running current is sufficient, and the load is not blocked. It is also not energy-saving. If the current is too small, the motor will not be able to carry the load at a high speed, and it is easy to block the rotor.
Regarding the red indicator light, it is always on to indicate normal operation, and the following conditions will cause the indicator light to flash:
. The drive fails to detect motor parameters after power-on because the motor is not connected or any phase of the motor is open circuit;
. Driver overcurrent protection.
Reminder: After the motor is connected, the main board will do the test at the moment of power-on. If there is a short circuit, open circuit and phase difference, the main board ALM warning light will flash, and the driver will not work. will work fine.
Package list:
1*DM542X digital DSP 42/57 stepper motor driver"
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Fill your shipping info
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.