Shipper/Relister:

1) The button pad for this remote is interchangeable with stock # 558

2) The circuit board in this remote is identical to circuit boards in stock #s 558, 560 & 560A

3) These remotes are interchangeable with remotes in stock # 558, 560 & 560A



 One (1)

Aftermarket remote keyless entry fob alarm

Transmitter control clicker keyfob controller replacement

Functions at 100% Tested & Guaranteed

 Audiovox / Prestige / Pursuit / Pro

 

FCC ID: ELVATCC

Interchangeable FCC IDs

GOH PCMINI

ELVATCC

GOH-PCMINI-4Q

 Interchangeable Part #s

07S1BP

07S1BPR

AVX-1B4S

3671A10247510

3671A10308381

 Interchangeable circuit board #s: 

ATCD-1

ATCN-1

ATCD

 Frequency: 433 – 434 MHz

 LED color: Red

 1 button

 Battery: (2) CR 1220

 

 

Compatible with the following systems:

APS900

APS901

APS901C

APS901N

AS9055C

AS9055T

AS9233ST

JKRS1

JKRS1T

PRO9051N

CA421

CA420A

CA420

CA440TW

CA440SS
 

 

Programming Instructions:

METHOD #1

NOTE: All applications require that tach be programmed.

The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored.

If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and could re-engage the starter motor.

The Remote Car Starter will learn the tach rate of most vehicles single ignition coils, multiple coil packs, and or single injector.

TO LEARN TACH:

1. Turn the ignition key to the ON position.

2. Press and release the program push-button switch 3 times.

3. Immediately turn the ignition key OFF.

4. Hold the program push-button switch ON, then start the vehicle using the ignition key.

5. When the unit senses the tach signal, the parking lights will begin to flash.

6. Release the program push-button switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored and the unit is now out of the program mode.

 

METHOD #2

  1. Turn the ignition to the on position.
  2. Press and release the programming switch 3 times.
  3. Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes, indicating the transmitter has been learned.

Repeat step 3 for up to a total of 4 transmitters.

Note: Do not allow more than 15 seconds to lapse between steps or the program mode will be automatically exited and you will have to start over.

 

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.


We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.

Please Note: Each remote and circuit board is UV id’d prior to shipment  – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.

Does this keyless remote entry come with a battery?  

Yes. It will have a working battery installed.

Battery Condition:

        A. All remotes sold on Keyless4u include working batteries.

        B. Installed batteries are not tested for battery life- they are simply working.

             Some are new and some are used.
 
Your vehicle will be installed with one of the following keyless entry systems:  

  a. Standard Keyless Remote Packages: Installed at time of manufacture. 

  b. Optional Keyless Remote Packages: Installed by a dealer. 

  c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. 

  d. No remote keyless entry system at all.

The above information can change which remote you need
for your installed remote keyless system.