1804 2400KV Outrunner Brushless Motor for 240 250 FPV Multicopter7859
1804 2400KV Micro-Type Size Outrunner Brushless Motor.As of testing, full load of this motor demands between 6A - 8A current. So a Greater than10A ESC is recommended, a 6A ESC might be too low if you need to drive it very hard.This is a great little motor suitable for multirotor helicopters size between 200-330mm.
Washer Needed?Depends on the thickness of the frame which you will install this motor, you might need to use a washer with the screws because they might be too long if your frame is thin.So you need to check this carefully during the installation(to see whether the screw is too close to the motor wire inside. If yes,then you need to use a washer).The Washer needed is M2 Washer.Beside using washers,you may also consider to use shorter screws eg.2x5 or 2x4 depends on the thickness of the frame.
The thickness of the frame that this motor was originally designed for is 2.2mm. The screw is about 2x6 (Diameter is about 2mm and the total length is about 5.8mm). So in that case if the thickness of your frame is less than 2.2mm, then you might need to use a Washer, and you need to check carefully during installation whether the screw is too long which touches of the wire inside the motor.
Description:
Motor Diameter: . 23.6mm
Motor Shaft Diameter: 5mm
Capable of 6-12~ amps of power draw
Motor wire length = 40mm
Which ESC is suitable for this motor?
The testing (with 3S Li-Po, 10A ESC and both 5030 2-Blade & 3-Blade Propeller) shows that this motor demands between 7.5 - 8.5A during full load ( Throttle). So a 10A ESC is preferred to avoid overheat if you plan to drive this motor hard. The temperature of 10A ESC was only a little warm after a continuous full load after 5-6 minutes.
10A G Series SimonK (better option)
10A Series SimonK (economy option)
A wholesales customer reported that the motors work beautifully which he used 4S 2200mAh
Washer Needed?Depends on the thickness of the frame which you will install this motor, you might need to use a washer with the screws because they might be too long if your frame is thin.So you need to check this carefully during the installation(to see whether the screw is too close to the motor wire inside. If yes,then you need to use a washer).The Washer needed is M2 Washer.Beside using washers,you may also consider to use shorter screws eg.2x5 or 2x4 depends on the thickness of the frame.
The thickness of the frame that this motor was originally designed for is 2.2mm. The screw is about 2x6 (Diameter is about 2mm and the total length is about 5.8mm). So in that case if the thickness of your frame is less than 2.2mm, then you might need to use a Washer, and you need to check carefully during installation whether the screw is too long which touches of the wire inside the motor.
Description:
Motor Diameter: . 23.6mm
Motor Shaft Diameter: 5mm
Capable of 6-12~ amps of power draw
Motor wire length = 40mm
Which ESC is suitable for this motor?
The testing (with 3S Li-Po, 10A ESC and both 5030 2-Blade & 3-Blade Propeller) shows that this motor demands between 7.5 - 8.5A during full load ( Throttle). So a 10A ESC is preferred to avoid overheat if you plan to drive this motor hard. The temperature of 10A ESC was only a little warm after a continuous full load after 5-6 minutes.
10A G Series SimonK (better option)
10A Series SimonK (economy option)
A wholesales customer reported that the motors work beautifully which he used 4S 2200mAh
