Fits: 

Please do not make any assumptions as far as fitment is concerned. You must verify that this part will fit your exact model and specifics by doing the following:

1) See the table below if your model is included. If so, then

2) Go to the compatibility chart of the listing above.  If you can’t see the compatibility chart, then click on “see compatible vehicles” at the top of the listing to display the chart.

3) Locate your vehicle in the chart by year, make, model….etc.

4) The left most column, is the notes column with important details. Any restrictions or specifics for which this part will or will not fit will be included in these notes.

In general, the drive of your vehicle (4WD, AWD, ….etc) needs to be known.  Also how many drive shafts does your vehicle have? On which drive shaft you want to install the U-Joint and where on that shaft (front, rear, at transmission….etc.)

AMERICAN MOTORSAMX1978-1980
AMERICAN MOTORSCONCORD1978-1982
AMERICAN MOTORSEAGLE1980-1981
AMERICAN MOTORSGREMLIN1975-1978
AMERICAN MOTORSHORNET1975-1977
AMERICAN MOTORSMATADOR1975-1978
AMERICAN MOTORSPACER1975-1980
AMERICAN MOTORSSPIRIT1979-1982
CHRYSLER3001958-1964
CHRYSLERCORDOBA1975-1983
CHRYSLERFIFTH AVENUE1983-1986
CHRYSLERIMPERIAL1958-1983
CHRYSLERLEBARON1977-1981
CHRYSLERNEW YORKER1958-1982
CHRYSLERNEWPORT1960-1981
CHRYSLERSARATOGA1958-1960
CHRYSLERTOWN & COUNTRY1975-1981
CHRYSLERWINDSOR1958-1961
DODGE8801963-1964
DODGEA1001964-1970
DODGEA108 VAN1967-1970
DODGEASPEN1976-1980
DODGEB1001971-1980
DODGEB1501981-1987
DODGEB2001971-1980
DODGEB2501981-1987
DODGEB3001971-1980
DODGEB3501981-1987
DODGECB3001973-1980
DODGECHALLENGER1970-1974
DODGECHARGER1966-1978
DODGECORONET1958-1976
DODGECUSTOM1958-1965
DODGED100 PICKUP1960-1987
DODGED150 PICKUP1977-1987
DODGED200 PICKUP1960-1980
DODGED250 PICKUP1981-1988
DODGED300 PICKUP1960-1980
DODGED350 PICKUP1981-1988
DODGEDART1960-1976
DODGEDIPLOMAT1977-1985
DODGEMAGNUM1978-1979
DODGEMIRADA1980-1983
DODGEMONACO1965-1978
DODGEP1001962-1968
DODGEP2001961-1974
DODGEP3001969-1974
DODGEPOLARA1960-1973
DODGERAMCHARGER1974-1987
DODGEROYAL MONACO1975-1977
DODGEST. REGIS1979-1981
DODGEW100 PICKUP1960-1987
DODGEW150 PICKUP1977-1987
DODGEW200 PICKUP1961-1980
DODGEW250 PICKUP1981-1988
DODGEW300 PICKUP1975-1980
DODGEW350 PICKUP1981-1987
FARGOA100 VAN1964-1969
FARGOA108 VAN1967-1969
FARGOB200 VAN1971-1972
FARGOB300 VAN1971-1972
FARGOD100 PANEL DELIVERY1966-1967
FARGOD100 PICKUP1966-1972
FARGOD110 PICKUP1966
FARGOD200 PANEL DELIVERY1966-1967
FARGOD200 PICKUP1966-1972
FARGOP200 PARCEL DELIVERY1961-1971
FARGOP300 PARCEL DELIVERY1969-1971
FARGOW100 PANEL DELIVERY1966-1967
FARGOW100 PICKUP1966-1972
FARGOW200 PICKUP1966-1972
JEEPCHEROKEE1974-1979
JEEPJ-1001966-1969
JEEPWAGONEER1966-1979
PLYMOUTHBARRACUDA1964-1974
PLYMOUTHBELVEDERE1958-1970
PLYMOUTHDUSTER1970-1976
PLYMOUTHFURY1958-1978
PLYMOUTHGRAN FURY1972-1985
PLYMOUTHGTX1968-1971
PLYMOUTHPB1001975-1980
PLYMOUTHPB1501981-1983
PLYMOUTHPB2001975-1980
PLYMOUTHPB2501981-1983
PLYMOUTHPB3001975-1980
PLYMOUTHPB3501981-1983
PLYMOUTHPLAZA1958
PLYMOUTHROADRUNNER1968-1975
PLYMOUTHSATELLITE1965-1974
PLYMOUTHSAVOY1958-1964
PLYMOUTHSCAMP1971-1976
PLYMOUTHTRAILDUSTER1974-1981
PLYMOUTHVALIANT1960-1976
PLYMOUTHVOLARE1976-1980
PONTIACGRAND LEMANS1975-1981

Premium; Greasable
MOOG premium universal joints are machined to meet or exceed original equipment standards. Each u-joint part is precision-ground to the strictest tolerances, with quality control inspections at every step of the manufacturing process.

Features

  • Bearing cups are cold-formed and case-hardened, then precision-ground to meet or exceed OE standards, for better wear and strength.
  • Superior quality seals are designed to keep contaminants out and to allow for proper lubrication.
  • Needle bearings are precision ground for maximum load-carrying capabilities.
  • Bearing cups utilize a radial design to allow 360° lubricant distribution to all bearing surfaces.
  • High strength steel crosses are forged to meet or exceed OE specifications and are carburized heat-treated for long life.
Specifications
Bearing Cap Axis 1 Diameter - Inch1.078
Bearing Cap Axis 1 Diameter - mm27.3
Bearing Cap Axis 2 Diameter - Inch1.078
Bearing Cap Axis 2 Diameter - mm27.4
Bearing Cap Type4 Grooved Round Bearings
Bearing Diameter A - Inch1.078
Bearing Diameter A - mm27.3
Bearing Diameter B - Inch1.078
Bearing Diameter B - mm27.4
Bearing Type ARound Grooved
Bearing Type BRound Grooved
GreasableYes
Length A - Inch2.125
Length A - mm54.0
Length Axis 1 - Inch2.125
Length Axis 1 - mm54.0
Length Axis 2 - Inch2.125
Length Axis 2 - mm54.0
Length B - Inch2.125
Length B - mm54.0
Length Measurement AOutside of Groove to Outside of Groove
Length Measurement BInside of Groove to Inside of Groove plus thickness of 2 Lock Rings
Lube Fitting LocationRegular Lube Fitting in Cross
LubricateableYes
OE SeriesDetroit 7260
U-Joint Identification4 Grooved Round Bearings