SUPER STRONG LONG LİFE HYDROGEN GENERATOR HHO DRY CELL 11 PLATES
THE PRODUCT IS SUITABLE FOR SMALL TORCHES AND ENGINES UP TO 2.0 LT. IT HAS LONG-LASTING THICK SEALS AND END PLATES RESISTANT TO ALKALINE CHEMICALS. YOU KNOW: YOU CAN INCREASE YOUR FUEL SAVINGS BY UP TO 35% BY USING HYDROGEN CELLS. IN SOME CASES EVEN UP TO 50%, BUT THIS DEPENDS ON THE CHARACTERISTICS OF THE ENGINE. THIS IS A CHEAP SOLUTION FOR THOSE WHO WANT TO SAVE SOME MONEY AS ALL KITS ARE MUCH MORE EXPENSIVE. THE PRODUCT IS MADE FROM THE BEST COMPONENTS THAT ARE RESISTANT TO ALKALINE CHEMICALS. IF YOU ARE NOT SURE WHICH HYDROGEN CELL YOU SHOULD BUY, YOU CAN CONSULT US.
ABOUT THIS PRODUCT:
-11 PIECES SPECIAL SUPER STRONG STAINLESS SHEET (100X100X0.5mm),
-CELL DIMENSIONS - 105mmX105mmX100mm,
-12 PIECES GALVANIZED PLASTIC COATED BOLTS
-HIGH QUALITY EPDM THICK GASKETS,
-BEST QUALITY STAINLESS METAL CONNECTIONS THAT PREVENT YOUR ENGINE FROM DAMAGE FROM RUST OR MOLTEN PLASTIC PARTS,
-2 CONNECTOR
-END PLATES MADE OF 10mm THICK ACID-RESISTANT AND LONG-LASTING HDPE MATERIAL
-PRODUCT READY TO INSTALL YOUR VEHICLE,
-For Engines up to 2.0 LT
-ALL PLATES LASER CUT,
-MY CELLS ARE MADE OF BETTER QUALITY COMPONENTS THAN OTHER CELLS ON THE MARKET.
Why this structure:
Plates:
Our plates have a special alloy. We do not use 316L or 316Ti. We called this special alloy super strong. We do not disclose the alloy content as it is commercial information. Its difference from 316L plate is that it lasts 30 times longer.
When using 316L, the cell needs to be cleaned after approximately 1000km of use. The water turns rusty brown. After 4-5 cleanings in total, the cell reaches the end of its life.
Super strong plates are cleaned once every 30 thousand km. During this period, the electrolysis water remains clean. Total lifespan is over 150 thousand km. We have customers who have been using these cells in their vehicles for 8 years and they are still very satisfied.
Stainless Metal connectors: Metal connectors are some of the most expensive connectors on the market but they are perfect for hho generators. Metal connectors do not crack and are not affected by corrosion. Unlike plastic connectors, they do not break in a short time as a result of heating and cooling of alkaline chemicals.
End plates:
HDPE is acid resistant and will not crack. The best choice when it comes to hho generators. There are also Plexiglas end plates on the market and these are much more likely to crack.
Gaskets:
We use acid-resistant gaskets to ensure long-lasting operation. What we have learned is that EPDM gaskets are perfect for hho generators. Natural rubber is not resistant to alkaline chemicals. Don't let them fool you. The gasket we use is manufactured and certified in the EU. The gaskets we use never melt or disintegrate.
Why this type of structure:
The Hho generator will need to be cleaned once every 30 THOUSAND KM ON AVERAGE. It is possible to clean the cell in 5 minutes without disassembling it, using the method specified in the user manual. One of the biggest problems experienced in other four-bolt cells is fluid leakage as a result of the caps being bent. In our 12-bolt cell, the covers never bend as the bolts hold the covers tightly at equal intervals. When you tighten the bolts to prevent leakage in 4-bolt cells, the covers become more bent after a while and leak again.
Working voltage: 12-14 volts
Working current: 0-20 amps
Gas production: 1000 ml/min at 20 amps
Pipe connection: 8mm hose