Recessed D-Ring and Backing Plate, 2-Pack


Set of Two D-Rings and Two Backing Plates

6,000 lb.cap.*

This product is available in a 3, 4, 6, 8, 9, 10, 12, and a 20 Pack. Search: Recessed 6,000 lb. - to find the other multi packs.

This listing is also available with  Hardware Kits.

The tie down attachment has a 6,000 lb. vertical pull weight rating*. To install this attachment requires routing, or cutting a hole in the floor.

The steel attachment is zinc coated to inhibit corrosion. When in use the ring portion raises for application and lies down when not in use, thus creating a flush surface. It is plenty strong and is able to receive multiple tiedown straps simultaneously. To obtain maximum strength it is recommended to install these d-rings with bolts, lock nuts, and fender washers (wide diameter).

This recessed d-ring has square holes punched for receiving carriage bolts, providing a smooth and relatively "trip free" surface.

Installation:

First determine the desired locations. Suggestion: Attach these tie-downs as close to a floor beam as possible. That is where the plywood/floor is strongest. If you installed in the middle between 2 floor beams the attachment won't be as strong.

Cut the opening using a 3-1/2” hole saw. If you do use a 3-1/2" hole saw, the d-ring will fit without any further work except drilling the bolt holes. The next step would ideally require a template. If you don't have a hole saw bit you can drill a small hole and cut the opening with a jigsaw. After cutting the hole place the ring in place and then proceed to mark where the bolt holes are to be drilled using a 3/8" drill bit. Preferably a wood bit although a standard drill bit will work.

.
Hardware Kits (lock-nuts, bolts, & washers) are available in our eBay store.

 

RECESSED D-RING SPECIFICATIONS:
  • 6,000 lb. rating (straight pull). WLL is 2,000 lb. capacity*.
  • The base measures 5" x 4-1/2"
  • Hole pattern is 3" x 3-1/2" on centers.
  • Recessed dimension is 2-1/2" in diameter with a flat edge.
  • The 7/16" diameter ring measures 1-3/4".
  • The ring pivots on a 5/16" threaded stud.
  • The pan has a 1/4" drainage hole
  • Weighs 1.2 lbs.


*RATED CAPACITY: Also known as "assembly capacity" or "break strength" is the minimum load a complete assembly can withstand before failure in a laboratory pull test when the product is NEW.

WORKING LOAD LIMIT: The maximum load weight a tie-down should be subjected to during normal use. To assist in making the proper tie-down choice the Federal D.O.T. requires the W.L.L. to be 1/3 of the Rated Capacity.


The backing plate is used for support under the floor when installing the attachments, and prevents the bolts from pulling through. It is meant to be utilized with the recessed 6,000 lb. d-ring, square hole style, included in this combination deal (pictured above).

Forged in Ohio

BACKING PLATE SPECIFICATIONS:

  • The backing plate measures 6" x 6".
  • Thickness is 11 gauge (a little less thick than 1/8).
  • 3/8" holes.
  • Offset 3-1/2" diameter cutout.
  • Steel backing plate is galvanized coated to inhibit corrosion.
  • Each plate weighs 14.3 ounces.

****Shipping applications - Shipping is done using UPS Ground or USPS Priority Mail. The FREE shipping rate is for the USA and its' Territories. International shipping is done thru eBay's Global Shipping.

Please contact us at 856-374-4740 with any questions or comments.

Telephone customer service hours: Mon-Thurs 7am-9pm EST Fri-Sat 7am-5pm