ARM DSO 202 Nano Pocket-Sized Digital Oscilloscope Tips: This pocket oscilloscope is primarily used for applications in the following situations: 1. Repair common electronic equipment outside (Air conditioning or Industrial frequency inverter power supply, AC / DC switching power supply or inverter, elevator and building fire safety equipment, industrial control circuit) 2. Hardware maintenance or software debugging RS232, RS485, I2C, CAN and other communications interface circuits, LED display and keyboard scan driver circuit, brushless motor drive circuit 3. Audio equipment and circuits, electronic toys and remote control models, car repair electronic circuits 4. School after-school teaching practice and student development of electronic small production 5. Need to slow signal changes observed applications (such as: relay and switch contacts jitter, battery charge and discharge curves of the load transient response power supply, temperature sensor features measurement) 6. The related supply t electronic circuit (SCR voltage regulator, power factor correction, electronic energy saving lamps, dysprosium lamp mercury lamp sodium lamp xenon lights drive circuit), As for other issues such as: CPU clock, RAM access, bus and USB or Ethernet signal measurement, high frequency and the video circuitry and the need to use FFT for signal analysis and so on occasion, The oscilloscope valued less than $1000 are not necessarily qualified for these. We advice to buy high-end oscilloscope! Deserves special mention is this pocket-sized internal battery-powered oscilloscope can be used, so in the field measurement, Ground is completely suspended, can be completely the same as multimeters, which measure what point, do not consider the issue of ground isolation. DSO202 is a pocket size digital storage oscilloscope fulfills basic electronic engineering requirements. It is has a dual trace three lines, new kind of system interface, capacitive convenient operation. You can easily operate it with the gestures of one-click, double-click, press and slide. The Aluminum shell is very fashionable. It is equipped with 320*240 color display, 8M Memory Card (U Disk), and chargeable Lithium batteries. The thickness is 11mm only! The volume is small enough to take it anywhere. It can meet the demands in many fields, such as, school experiment, electronic repairing and electric engineering. DSO series | DSO Nano (DSO201) | DSO Touch (DSO202) | DSO Quad (DSO203) |
---|
Sample rate | 1 MSps | 10 MSps | 72 MSps |
---|
Channels | 1 | 2 | 2 analog, 2 digital |
---|
Waveout | No | 1 MSps | 1 MSps |
---|
ADC | STM32F103 internal | STM32F303 internal | AD9288-40 |
---|
FPGA | No | No | ICE65L04 |
---|
RAM | 20 kB | 48 kB | 48 kB |
---|
Controls | 7 buttons | 1 button, touch area | 4 buttons, 2 scrollers |
---|
User interfaceDespite the name, the DSO Touch does not actually have a touch screen, just a capacitive touch area. But it does work a lot better than the crappy scrollers on DSO Quad. The early application seems to be a bit unresponsive at times, but is already a lot better than the original DSO Quad application ever became. Hardware The main PCB contains: STM32F303VCT6 processor: 72 MHz Cortex-M4F, 256 kB flash, 40 kB RAM HC4053 analog switch, used for gain selection Haier HC64005 touch area controller Winbond 25064 SPI flash chip AXP192 li-ion charger
Specification Analog bandwidth: 1MHz Max sample rate: 10MHz Sample memory depth: 8K Analog Input impedance: 1MΩ Max input voltage:±40v (×1 probe) Coupling: AC/DC Analog input sensitivity: 10mV/Div~10V/Div (1-2-5 Step) Vertical position: Adjustable with indicator Horizontal sensitivity: 1uS/Div~10S/Div (1-2-5 Step) Horizontal position: adjustable with indicator Independent Channel Display:-A,-B, A+B, A-B, RecA, RecB Trig modes: Auto, Norma, Single, None and Scan Rising/falling edge trigger ,Maximize/Minimize level trigger Automatic measurement: frequency, cycle, duty, peak/effective/Maximum/Min/average NO.of Voltage Test signal: Built-in 10Hz~1MHz or 10~20kHz Analog sine wave/ Triangle wave/ Sawtooth Wave Waveform storage: 8MB Memory Built-in: 600mAh Chargeable Lithium battery / USB Color TFT LCD display Resolution: 320×240 Input: Capacitive touch and slide gesture Dimension: 100mm X 56mm X 10mm Package List DS202 Body with Battery *1 Probe *1(X1/X10)
We accept PayPal and all major credit cards, including Visa, Master Card,, American Express, Discover, etc.
II. SHIPPING
We ship by Australia Post or others ways per customer's request. We ship out product every 3 daysIII. RETURN/EXCHANGE Return Policy: 1. There is a 5% or 15% restocking fee for unopened or opened items respectively. 2. Items with marks or alternated cannot be returned because we cannot resell them. 3. Items should be returned with original packaging materials and accessories. 4. Please put a note inside the package indicating your eBay user name, purchase date, and the reasons for returning. 5. Buyers pay for shipping the items back and the original shipping fee to the buyer will be deducted from the refund.
We have full time staff answering phone calls for technical and sales related question from 8am to 5pm AEST and reply eBay or email messages within 1 day. Please feel free to send us messages, we are all ears. About this instrument: our company, Analog Technologies, Inc., has been designing and developing analog electronic products for 24 years. This item has been used and highly recommended by our electrical engineers. Its user manual can be found online or downloaded from our company's website. That's why we are selling it here with the confidence that you will like it as well. Only if you are happy with our products and services then we will be happy. About us: Our company, Analog Technologies, Inc., was started as an R&D firm in January 7, 1997, in Novi, Michigan, a small town 25 miles from Detroit. After 24 years hard working, we have established branches in San Jose, California, USA; Sydney, Australia; and Anshan, Liaoning, P.R. China. We have 3 departments: R&D, Production and Trading. The products sold on eBay are either produced by our own Production Department or our sub-contractor companies. If you have any questions and/or suggestions, please contact us. Our goal is to make our customers happy and grow our company to a bigger one.
|
|