CARLIN EZ PRO
OIL to GAS conversion burner
model #9859210FRU
**NEW DIGITAL CONTROL BOX NOW INCLUDED INSTEAD OF ONE SHOWN**
This burner will install to your current boiler, furnace or water heater. It features a fully adjustable mounting flange to set your 'insertion depth' properly. You MUST clean your current boiler, furnace, or water heater thoroughly with brushes and a shop-vac to assure proper venting of the exhaust gases when converting from oil to gas. You will probably also need to purchase a special gas spill switch and special gas damper for your gas conversion which we can assist you with or sell you if not locally obtainable in your area.
PLEASE DO NOT ASK IF THE BOILER IS INCLUDED!!!!!
IT IS NOT!
PLEASE READ INSTRUCTION MANUAL TWICE BEFORE PERFORMING ANY WORK!
***this burner will be shipped to you in a factory sealed box***
[complete with gas valve, gasket, nipple, wire nuts, & all hardware]
**the photos show a standard unit with custom installation.
Yours may have a different band installed, a different plate installed, a different size orifice installed, may have the gas inlet on the opposite side, may have a different gas manifold valve, -
***EACH UNIT NEEDS TO BE CUSTOMIZED TO YOUR SPECIFIC APPLIANCE &
BTU INPUT RATING!***
----------------------------------------------------------------------------------------------------------
***NEW STYLE DIGITAL CONTROL BOX IS NOW STANDARD!***
FULLY PROGRAMMABLE BY INSTALLER & USER!
SET PRE-PURGE, TFI, & POST-PURGE TIMERS!
FULL HISTORY LOG OF LAST 50 FIRE-UPS!
FULL DIAGNOSTICS!
--------------------------------------------------------------------------------------------------
This burner requires much set-up work!
BEWARE OF OTHER SELLERS!
***SOME SELLERS WILL SELL YOU THIS EXACT BURNER FOR LESS AND LEAVE YOU HOLDING THE BAG!
WE ARE THERE FOR YOU FROM START TO FINISH FOR ADVICE.
TECH-SUPPORT ALSO AVAILABLE ON A TIME BASIS.
ABOUT OTHER SELLERS SELLING THIS UNIT:
NORMALLY--THERE IS ALOT TO DO ON THIS UNIT BEFORE YOU ARE READY TO INSTALL IT.
PLEASE DO NOT THINK THAT YOU JUST BUY IT AND INSTALL IT AND YOU ARE DONE
(that is what other sellers tell you)
---NO--NO---NO!
THERE IS DRILLING, DE-BURRING, ASSEMBLY PREPARATION, PIPE JOINT COMPOUND,
BAND CHOICE & ADJUSTMENT AND BAFFLE SELECTION!
THEY DON'T DO ANYTHING FOR YOU EXCEPT SELL YOU THIS UNIT.
WE WARRANTY THIS UNIT & WILL COVER ANY
NON-FUNCTIONAL COMPONENT FOR
A FULL 2 YEARS FROM THE DATE OF PURCHASE!
(BUYER PAYS SHIPPING BOTH WAYS--THE PART IF FREE!)
This is the burner that should be used in almost every gas conversion job around. It is virtually maintenance free, SUPER RELIABLE, and it is a NAME BRAND item!
This burner requires much set-up work!
BEWARE OF OTHER PATRIOTIC SELLERS ON EBAY WHO ATTRACT YOU WITH FANCY BANNERS, FLAGS, CLOWNS, OR DANCING BEARS! THEY WANT YOU TO BE PATRIOTIC TO THEM BUT IN FACT THEY ARE NOT EXPERIENCED CONTRACTORS AND WILL FORGET YOU RIGHT AFTER THEY MAKE THE SALE. THEY ONLY SELL THE UNIT AND LEAVE YOU HIGH AND DRY AFTER THE SALE!
THEY HAVE NO ASSOCIATION OR EXPERIENCE WITH THE ACTUAL INSTALLATION AND MAINTENANCE OF THESE UNITS AND CANNOT AND WILL NOT EVEN ADVISE YOU ON ANY ISSUES YOU MAY HAVE!
THEY CLAIM IT IS A LIABILITY ISSUE---THEY JUST DON'T KNOW. THAT IS THE TRUTH!
ALL YOU WILL NEED TO DO IS TO FOLLOW THE SAMPLE PICTURES AND MAKE YOUR PLUMBING LOOK JUST LIKE THE PICTURES IN THE INSTRUCTIONS AND PRESSURE TEST THE PIPES WHEN DONE. WHEN FINISHED YOU WILL NEED TO HAVE AN EXPERIENCED TECHNICIAN DO A COMBUSTION ANALYSIS TO OPTIMIZE EFFICIENCY AND TO MINIMIZE ANY NOXIOUS EXHAUST GASES.
WE WARRANTY WHAT WE SELL USUALLY LONGER THAN THE MANUFACTURER DOES.
BUY FROM US WITH CONFIDENCE!
WE ARE EXPERIENCED CONTRACTORS AND KNOW HOW TO DO IT RIGHT SO WE CERTAINLY CAN ADVISE YOU HOW TO DO THIS JOB RIGHT IF YOU RUN INTO DIFFICULTY!
Technical support from us is NOT normally included with THIS item purchase
but we will help you on some issues if you are having difficulty.
*****If you feel that you need COMPLETE technical support from US
from beginning to finish please purchase
item number 331904425453 instead. *****
That item number includes COMPLETE technical support from beginning to finish as required.
(We are not like the OTHER GUYS! We will be with you for LIMITED technical support post-sale to complete your installation!
You will be issued a cell phone number to our technical support technician upon receipt of your unit)
This unit requires precision drilling and reaming of the orifice for the proper BTUs desired.
You must give us the equipment information and BTU information from YOUR current unit FOR US TO ASSIST YOU WITH TECHNICAL SUPPORT.
***LIMITED TECHNICAL INSTALLATION SUPPORT IS INCLUDED BUT IS LIMITED TO THE IMMEDIATE AREA NEAR THE BURNER UNIT ITSELF---NOT THE PLUMBING FROM THE SUPPLY TO THE UNIT.
***LIMITED ELECTRICAL TECHNICAL SUPPORT IS ALSO INCLUDED WITH THE PURCHASE OF THIS UNIT BUT IS LIMITED TO WIRING TO THE BURNER ONLY AND DOES NOT COVER ANY WIRING PREVIOUSLY NOT INSTALLED TO CODE OR INSTALLED IN AN IMPROPER MANNER.
This burner also requires COMBUSTION TEST EQUIPMENT when INSTALLATION IS COMPLETE to be able to measure the exhaust gases and determine if the combustion is safe & correct.
Adjustments can be made depending on the Test Equipment readings and should be done by a licensed GAS technician.
NOTE:
This unit should be installed by an experienced gas installer/service technician BUT if you are mechanically inclined and know gas plumbing and some electrical, you can do most of the installation yourself and save big $$$$.
You WILL however need a technician when done to check your work for possible gas leaks with a pressure tester.
You will also need him to possibly fine-tune your combustion adjustments for proper burn and to adjust it for minimum noxious fumes and pollutants.
DISCLAIMER----PLEASE NOTE:
*Some localities may require a chimney liner be installed when using gas fired equipment. Please check your local codes.
*Most localities also require a pressure test (by a licensed gas plumber) of the gas plumbing whenever a change/addition is made to the new or existing gas plumbing.
*Also some localities may not allow a homeowner to perform his own gas plumbing or electrical work at all. Some do and require a pressure test as stated above. Check your local codes.
*We attempt to assist with technical guidance as best as possible with phone conversations and email/texts, Facetime™, and other media, however BUYER assumes all responsibility when purchasing this product as we cannot guarantee the quality of work by anyone who is not licensed and/or experienced in the installation and use of this product.
*Incorrect or faulty installation of this product can cause serious injury or even death!
*Please check with your local gas plumber BEFORE putting any self-installed appliance into service.
*This unit is offered for sale to knowledgeable handymen and professionals who will also secure the assistance of a licensed gas plumber/electrician or technician to oversee the job. Buyer assumes any and all risks associated with the purchase, installation, and any related consequences in the installation and or use of this item.
SPECIFICATIONS:
BTU 50,000 to 275,000 BTU (precision drilling or orifice required--we can do it for you!)
[GREATER BTU AVAILABLE IF NEEDED--different models available at a higher price--up to 1,100,000 BTU]
| Electrical |
| Power: |
| Fuels |
| Natural Gas or Propane Gas (LP)
|
Carlin 9859210FRU Universal EZ-Gas Pro Gas Conversion Burner with 10" Air Tube and adjustable flange.
If a longer blast tube length is required please call our technical service department and we will help you determine which unit best suits your needs.
Burner Includes:
Diffuser Plates: Three diffusers are INCLUDED to accommodate various BTU input ranges:
• “A” Diffuser Plate: 175,000 - 275,000 BTU/H
• “B” Diffuser Plate: 50,000 - 175,000 BTU/H
• 9-Slot Diffuser Plate: 70,000 - 230,000 BTU/H
Air Bands: Two air bands are INCLUDED to accommodate various BTU input ranges:
• 1-Slot: 50,000 - 175,000 BTU/H
• 2-Slot: 175,000 - 275,000 BTU/H
Multi-Fit and Universal Burners include a Field-Drilled orifice. This orifice must be drilled in the field to suit the firing rate of the appliance.
Converts Oil-Fired Appliances to Natural Gas or Propane or REPLACES an existing gas burner.
Fires From 50,000 to 275,000 BTU/H
Ideal for
• Boilers - Pin-Style, Steel, Three-Pass
• Warm Air Furnaces
• Direct-Fired Water Heaters
Faster, Easier and More Cost Effective than Replacing the Heating Appliance
UL Listed
Carlin Universal Burners are available in two models ? one for boilers and one for furnaces and water heaters. Both include an adjustable mounting flange, all three diffuser plates, both air bands, and a field-drilled orifice. The only difference between the two is the air tube length. The boiler model is equipped with a 10" tube, more than adequate for the insertion depth on most boilers. The water heater and furnace model has a 14" tube better suited for deeper insertion depths. These universal burners can be configured in the field to accommodate virtually any heating appliance.
Technical support may be reached at 'Boilers R Us' ---- 631-404-2454 or 631-236-7397.
CUSTOM ORDERS (like this one) usually ship within 72-96 HOURS.
This item ships out of our LINDENHURST, NY 11757 shipping facility.
We are no longer permitted to display our telephone number as per eBay policy.
You may contact us by TEXT.
Sorry for the inconvenience.
‘BOILERS R US’ will ship this item to you directly.
**installation available in NY, NJ, CT, DE, MD, PA, VA, MA, RI, VT, MA,
for an additional fee ($850-$1500)***
ref: 26---16/16/24
We ship same day on most items however IF you selected EBAY SHIPPING which is a less expensive shipping service but usually takes longer to deliver to you, you will experience longer delivery times.
If not happy with the time it takes to receive this item please complain to ebay as I have selected 'NO EBAY GLOBAL SHIPPING? however eBay offers it and I have no choice after your purchase and selection based on their system.
PLEASE complain to eBay about this!
CALL THEM
(800) 456-3229
(866) 540-3229.
Thank you,
Charlie & the team