*NOTE: These are measured for fitment
by the mounting diameter on the carb,
not the carburetor bore or throat
size.
Also note: These come equipped with the longer lasting, higher
flow rate Stainless Steel, silver screens.
Sold one each, buy as many as you need, shipping is discounted automatically!
only $.01 cent for each additional, ~ if you choose Priority Mail!
NOTE on VM24 carbs:
These are 44mm, VM24 carbs are 43mm,
you will have to shim it with something,
extra screen material works well, let me know if you need some!
This listing is for 1 polished
aluminum
finish stack. -Sorry for any confusion with the
pics.You get 1 stack per order.
order as many as you need,
shipping is automatically discounted.
you get one full-taper Type velocity stacks per order,
with mounting setscrews and debris screen.
for VM26 VM28 (and other 44mm OD carbs)
DOES NO FIT PE28 you MUST measure first!
60mm or 2.4" in length
44mm ID at carb where it slides on / Approx. 43.5mm with screen installed
50mm OD at carb side where slides on.
bellmouth (widest / OD) 62mm or 2.5"
Flange mount depth: 9.5mm
These are made specifically for
VM26's VM28 and other 44mm carb mounts.
There are no better designed velocity stacks, at any price!
I also have CB750 stacks & many others:
https://stores.ebay.com/CycleSmith-parts-accessories?_dmd=1&_nkw=velocity
---------------------------------------------------------------------
Color/Finish: Polished Billet Aluminum
Fits: 44mm carb mouth diameter.
Material: Billet Aluminum, held with setscrews
--------------------------------------------------------------------------------------------------------------------------
Q: what are the jetting specs for an xxx?
A:
Sorry, i don't know the exact jetting specs for your specific bike.
--as you may know, XXXX's used various carbs with different jet sizes.
Also, note that every bike is different, and important factors, such as what exhaust you're running,
and your elevation, engine condition, etc. all have an effect.
On my XXXX with stock exhaust, here in CA at about 1000 ft above sea level,
i didn't have to rejet, (chage jet sizes) we just adjusted the carbs-
idle mixture adjustment, possible needle adjustment and finally a good carb synch (synchronization).
But a bike with drag pipes or 4:1 is going to be very different!!!!
Check an online forum, someone out there has the same year bike,
with the same intake and exhaust setup as yours, and you can get
their jetting specs.
As a general rule of thumb for jetting for velocity stacks,
most people bump the main jets up 1 to 2 sizes above the stock jetting.
In some cases, if the bike has stock mufflers, we can get away
with just an idle mixture adjustment and a good carb synch.
You would probably go up more sizes for straight/open pipes.
But the issue is that individual bikes are just too different to offer blanket advice for.
The types of muffler (or lack of a muffler), and header setup, your altitude, different cam shafts,
big bore kits, state of engine wear and tune,... they're all factors that change jetting specs.
So, the simplest thing to do is start out 1 to 2 sizes above stock, and experiment from there.
It is also recommended to check out the bike forums related to your model,
to see what other guys with similar bikes & setups are running theirs at.
most people bump the main jets up 1 to 2 sizes above the stock jetting.
In some cases, if the bike has stock mufflers, we can get away
with just an idle mixture adjustment and a good carb synch.
You would probably go up more sizes for straight/open pipes.
But the issue is that individual bikes are just too different to offer blanket advice for.
The types of muffler (or lack of a muffler), and header setup, your altitude, different cam shafts,
big bore kits, state of engine wear and tune,... they're all factors that change jetting specs.
So, the simplest thing to do is start out 1 to 2 sizes above stock, and experiment from there.
It is also recommended to check out the bike forums related to your model,
to see what other guys with similar bikes & setups are running theirs at.
Sorry, I do not sell jets. try a
local shop / K&L supply / SUDCO for jets.
----------------------------------------------------------------------------------------------------------------------------------------------------
ACTUAL EBAY FEEDBACK:
thanks for a easy transaction top notch items and look great +++++++++++++++++++++++
MIKUNI VM24 VM26 VM28 VM29 44mm VM KZ Velocity stacks Polished Stack sold 1 ea
Seller is amazing.
Quality product and economical price.
| Buyer: | During past month | |
| MIKUNI VM26 VM28 44mm VM KZ Velocity stacks Polished Velocity Stack SOLD EACH |
Great seller with quality made parts, Thank you.
| Buyer: | ||
| MIKUNI VM Velocity stacks Velocity Stack set of 2 |
Great seller. Thank you
| Buyer: | ||
| MIKUNI VM26 VM28 44mm VM Velocity stacks Polished Velocity Stack SOLD ONE EACH |
| The parts fit perfectly on my Custom Cafe with VM's. I could not be more pleased! | Buyer: | |
| Excellent product and service, highly recommended | Buyer: | |
| Thanks again!!!!!!!!!! |
||
Contact me with any problems.
Buyer to pay initial shipping cost as well as return shipping if returned
for reasons other than defect.
Please contact me before leaving neutral or negative feedback!
I have a 100% feedback rating !
as always, ask questions first before buying!