GY21-HTU21D Temperature & Humidity Sensor Module Breakout Board Module F Arduino
Features:
 
The HTU21D is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor.
This sensor is ideal for environmental sensing and data logging and perfect for a weather stations or humidor control systems.
All you need is two lines for I2C communication and you’ll have relative humidity readings
and very accurate temperature readings as a bonus!

There are only four pins that need to be hooked up in order to start using this sensor in a project.
One for VCC, one for GND, and two data lines for I2C communication.
This breakout board has built in 4.7k pull up resistors for I2C communications.
If you’re hooking up multiple I2C devices on the same bus, you may want to disable these resistors.

It's summer and you're sweating and your hair's all frizzy and all you really want to
know is why the weatherman said this morning that today's relative humidity would max
out at a perfectly reasonable 52% when it feels more like 77%.
Enter the HTU21D-F Temperature + Humidity Sensor - the best way to prove the weatherman wrong!

This I2C digital humidity sensor is an accurate and intelligent alternative to the much simpler
Humidity and Temperature Sensor - SHT15 Breakout It has a typical accuracy of ±2% with an
operating range that's optimized from 5% to 95% RH. Operation outside this range
is still possible - just the accuracy might drop a bit. The temperature output has
an accuracy of ±1°C from -30~90°C. If you're looking to measure temperature more accurately,
we recommend the MCP9808 High Accuracy I2C Temperature Sensor Breakout Board.
 
Such a lovely chip - so we spun up a breakout board that includes the
Filtered version (the white bit of plastic which is a PTFE filter to keep the sensor clean),
a 3.3V regulator and I2C level shifting circuitry. This lets you use it safely with any kind
of microcontroller with 3.3V-5V power or logic. Each order comes with one fully assembled
and tested PCB breakout and a small piece of header.
You'll need to solder the header onto the PCB but it's fairly easy and takes only a few minutes even for a beginner.
 
Board size:1.2x1cm(approx)
 

Package Included:

1 x GY21-HTU21D Temperature & Humidity Sensor Module Breakout Board Module For Arduino

We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can perform up your satisfaction. Then we will improve our service immediately.
It is impossible to address issues if we do not know about them.

  • We only accept payment through Paypal.
    Items will go to post within 1-2 business days after payment confirmed.
  • 1. We ship to Worldwide.
    2. We only ship to confirmed PAYPAL address; your PAYPAL address must match your Shipping address.
    3. Any non-received items caused by invalid address registered on PayPal are not in our full refund or replacement policy. Shipping fee has including the local handing and packaging fee.
    4. All the items will be shipping within 1-2 working days after receiving the payment, except some holidays.
    5. We will not be responsible for any custom delay or tax, because transit time is highly depended and provided by postal Service.
    6. If you have any problem, please contact us via message, we will reply message within 1-2 working days, please wait for patient.
  • All package need to wait 30-40 days,Please take care it.Less than 40 days,we can't take a refund.
  • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
  • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
DataCaciques