Sold one each, buy as many as you
need, shipping is discounted automatically!
only $.01 cent for each additional, ~ if you choose Priority Mail or Express!
100mm wire connector lengthonly $.01 cent for each additional, ~ if you choose Priority Mail or Express!
- Yamaha Maxim 650 XJ650 1980 - 1983
- Yamaha Maxim 750 XJ750 1982 - 1983
- Yamaha Midnight Maxim 650 XJ650L 1981
- Yamaha Midnight Maxim 750 XJ750M 1983
- Yamaha Seca 650 XJ650R 1982
- Yamaha Seca 750 XJ750R 1981 - 1983
- Yamaha Seca Turbo 650 XJ650 1981
- Yamaha Seca Turbo 650 XJ650L 1982 - 1983
This is great! Looks stock, enhances value!
Specifically designed for Yamaha XS and XJ & FZ600 series bikes:
I love to use them on my XS1100 projects, XS650, XS750/XS850,
XJ Maxims/Secas, early FZ's and other models!
The XS Fuse Boxes located on top of the battery,
or under the side panel, are a part of the original wiring harness,
- and until now, have Not been available separately.
This is a replica of that box as shown, plus matching terminal block & terminals.
None of the stock YAMAHA fuse boxes come removable from the factory.
This comes with all the terminals and connectors to splice into your wiring harness.
With the addition of the connector block, if you have problems down the line,
(in say, another 30-40 years), you can easily remove the whole box,
because you have already installed the quick snap connector!
Simply cut the old fuse box from your main harness,
(noting which wires go to which fuse circuit! :-), I like to go one at a time...lol
Install the supplied terminals, then attach the connector block (provided)
and plug in the new fuse box!
Here is a pro tip, ride the bike for 5 or 10 minutes,
and put you hand close to the fuses, touch them all quickly,
to see if they are warm, or hot to the touch.
If they are, there is resistance, usually the clips themselves are the culprit.
trying to clean them- with say, a dremel wire wheel, will often just break them,
because the heat has made them so brittle.
I recommend replacing them all, and checking again for heat.
I suggest that ALL the connectors on the bike, especially charging system,
and the ignition wires that go inside the headlight bucket, should be cleaned,
de-oxified, and packed with dielectric grease.
Includes 1 x 20Amp and 3 x 10Amp fuses.
And of course, you can substitute any amp fuse,
in any slot, as needed for your particular bike / circuit.
----------------------------------------------------------------------------------------------
Notes on installation:
recommended tools are: wire strippers and a crimping tool
*ask one of your buddies,
- someone is bound to have some crimpers you can borrow! lol :-)
* note: For better than Factory, professional results, the male connectors for the plug
*ask one of your buddies,
- someone is bound to have some crimpers you can borrow! lol :-)
* note: For better than Factory, professional results, the male connectors for the plug
should be soldered in place, once crimped to the wires. this eliminates pullout. *
-----------------------------------------------------------------------------
Shown below is a picture of the fuse box and connectors,
and above that is a battery cover intended for XS650 models
you can use this for any 4 fuse setup.
cut your old one out of the harness, and install the supplied terminals,
matching the wiring positions with your old fuse box.
and above that is a battery cover intended for XS650 models
you can use this for any 4 fuse setup.
cut your old one out of the harness, and install the supplied terminals,
matching the wiring positions with your old fuse box.
NOTE: THE LARGE BATTERY COVER for xs650 models is available.
You can buy this cover at a very low price, only $2.00
i will add it to your order if you want it.
------------------------------------------------------------------------------------------------------
ACTUAL EBAY FEEDBACK:
Just as described...Thank you. Could not be any happier.
You can buy this cover at a very low price, only $2.00
i will add it to your order if you want it.
------------------------------------------------------------------------------------------------------
ACTUAL EBAY FEEDBACK:
Perfect swap out for my Maxim and my wife's Seca. No problems since I put them in.
Buyer: alra_6705 (1)
Yamaha XS XJ RD RZ FZ600 TX XS650 XS1100 Fuse Box replacement OEM 4 Glass fuse
Just as described...Thank you. Could not be any happier.
| Buyer: | ||
| Yamaha XS XJ RD RZ FZ600 TX XS650 XS1100 Fuse Box replacement OEM 4 Glass |
| Item as described. Would definitely shop with this seller again. | Buyer: | |
| Yamaha XS XJ RD RZ FZ600 TX XS650 XS1100 Fuse Box |
| Great ebayer#1 !!!!!!!!! | Buyer: | |
| Yamaha XS XJ RD FZ XS650 XS1100 Fuse Box replacement OEM 4 Glass fuse |
| Thanks!!!!!!!!!!!! | Buyer: | |
| Yamaha XS XJ RD FZ XS650 XS1100 Fuse Box replacement ( |
| REALLY COOL JUST WHAT I NEEDED.5 STARS AND THANKS MUCH! | Buyer: | |
| Yamaha XS XJ RD FZ XS650 XS1100 Fuse Box replacemen |
| Product as advertised. Worked great! | Buyer: | |
| Yamaha XS XJ RD FZ XS650 XS1100 Fuse Box replacement |
| great e-bayer A++++ | Buyer: | |
| Yamaha XS XJ RD FZ XS650 XS1100 Fuse Box replacement |
| This thing is a drop in and works GREAT! Thanks for having it, A++ Dealer | Buyer: | 6 |
| Yamaha XS XJ RD FZ XS650 XS1100 Fuse Box replacement |
Contact me with any problems.
Please contact me before leaving neutral or negative feedback!
I have a 100% feedback rating !
as always, ask questions first before buying!
Please contact me before leaving neutral or negative feedback!
I have a 100% feedback rating !
as always, ask questions first before buying!