PIONEER PL-6 Original Record Player Turntable RARE Vintage 1960 Hi Fi Good Look

Pioneer PL-6

Pioneer PL-6A

24,000yen(middle of the 1960s)

Description

�@

The stereo record player which developed and carries an auto organization original with the base for PL-6.

4 pole synchronous motor is adopted as a motor.

For a synchronous type, it was not influenced by transition of a voltage or a load intensity, but the exact constant-speed rotation is realized.

The turntable made from aluminum alloy die-casting with a weight of 1kg is adopted as a turntable for 25cm in diameter which gave precise machining. .

even a lever operation comes out and the auto organization which rise and fall of a tone arm, on/off of a motor power source, an operation of an idler, etc. interlock and commit is carried.

The oil dumping arm elevation organization is carried and it goes up and down a tone arm by the suspension action in a spring and an oil cylinder.

A motor power switch is interlocked with an arm elevation organization, and operates. Only when a tone arm descends and it is in a performance state, it is set to being turned on, and it is come by off when an arm goes up. Moreover, an operation of an idler is also interlocked with.

Only while a tone arm descends and the motor is rotating by the idler auto controller, a motor shaft (capstan) and turntable inner circumference are pasted.

In addition, if an elevation lever is placed according to the location of Play, it is possible to carry out an on/off operation of a motor with a velocity change thumb as well as a common player.

The pipe type tone arm of the absent-resonance design type which carried out the work original with a manipulation of the pivot is adopted as a tone arm. Form serves as a static balance type suitable for stereophonic reproduction.

Moreover, the connector type head is adopted and a using of other cartridges is possible.

PL-C6 which is man-month type cartridge is adopted as the cartridge.

The full-scale structure which planted a 0.7mil diamond needle in the cantilever made from a duralumin pipe of 0.6mmphi is adopted, the needle point is considering it as the scheme which attached the whole needle to the holder of a plastics, and a tension favorable impression is simply possible for it.

Form Record player

Auto organization An oil dumping arm elevation organization is interlocked with.

Motor power-source auto switchpoint

Idler auto controller

Tone arm Static balance type tone arm

Motor 4 pole synchronous type

Turntable Diameter aluminum alloy die-casting of 25cm, 1kg

Rotation unevenness 0.2 or less

Rotational frequency 33 1/3, 45 or 78rpm

Cartridge man-month type (PL-C6)

SN ratio (at the time of PL-C1 using) 47dB or more

Starting time from a start-up Less than (33rpm) 1/4 rotation

Cartridge man-month type (PL-C1)

Frequency characteristic 20Hz-21kHz�}2dB

Channel isolation 20dB or more (1kHz)

Output voltage 5mV (at the time of 1kHz and 50 mm/s)

Output balance 2dB or less (at the time of 1kHz and 50 mm/s)

Impedance 1. 5kohm (1kHz)

Direct current resistance 500ohm

Load resistance 50kohm

Needle 0.7mil diamond needle

Needle point compliance 6x10 to 6 cm/dyne

Tracking error �}1.5 degrees

Proper stylus force 3g-4g

Switching needle Diamond needle for stereos PL-N6 (2,400yen)

Sapphire needle for SP monophonic recordings PL-N 6S (1,000yen)

Power source AC220V, 50Hz/60Hz switching type

Dimensions Width 475x height 190x depth of 380mm

https://audio-database.com/PIONEER-EXCLUSIVE/player/pl-6a-e.html

ATTENTION:

With small marks of use and the passage of time, Look carefully at the photos that show the real state of the article, We do not accept subsequent claims.