TRANSGO 4L60E 4L65E HD2 STAGE 2 SHIFT KIT REPROGRAMMING KIT


FITS ALL:

VS VT VX VU VY VZ VE 4 SPEED 4L60E 4L65E AUTO TRANSMISSIONS 


4 SPEED AUTO ONLY (WILL NOT SUIT 5 SPEED TRANSMISSIONS IN VZ SV6 CALAIS AND VE)



 COMMODORE ACCLAIM EQUIPE ESTEEM BERLINA CALAIS S SS SSZ ETC UTE SEDAN AND WAGON

VS VT VX VY VZ SERIES HSV CLUBSPORT R8 MALOO SENATOR XU6 XU8 SV6000 GTS GTO AVALANCHE XUV GRANGE ETC

VS WH WK WL STATESMAN AND CAPRICE

V2 VT VY VZ MONARO COUPE

VY VZ ADVENTRA CREWMAN



BRAND NEW GENUINE TRANGSGO PARTS, IN PACKAGING

This 4L60E-HD2 Reprogramming Kit fits 1993 to 2015 General Motors vehicles equipped with the 4L60E, 4L65E and 4L70E automatic transmission. Common complaints on this transmission are TCC slip or shudder, code P1870 or P0894, harsh 1-2 shift, double bump shifts, 2-3 flare up, burnt 3-4 clutch plates as well as inconsistent pressure boost problems.

The torque converter clutch regulator valve bore is very prone to wear causing the TCC slip complaints and related code. The TCC slip code leads to the harsh 1-2 upshift as the ECM recognized the TCC slip and commands high line pressure to avoid further TCC slippage and damage. The 3-4 clutch plate failure as well as the 2-3 flare up complaints are caused by an inconsistent pressure boost and poor overall calibration of the shift accumulation system.

Features and benefits:

This TransGo Reprogramming Kit includes valve body, servo, pump and accumulator components and modifications designed to deliver increased durability while providing firm shifts as well as a more efficient TCC apply. It includes components as well as modifications that recalibrates the entire accumulation system, clutch and band feed orifices. These changes work in concert with an aggressive line pressure curve to greatly improve the overall durability and shift feel of the transmission. . Furthermore, the included drop-in USA-made TCC isolator and regulator valve features longer lands which restores the hydraulic integrity of the circuit by utilizing previously unused and therefore unworn areas of their bore. Lastly, on 1993 to 2008, the gear command feature will allow for full gear lever controlled downshifts 3rd through 1st gear as well as holding manual 1st or 2nd gear to any speed or RPM.

This kit can be installed while the transmission is in the vehicle on models without the input speed sensor(input speed sensors are usually only in the 4L65E versions).  

This kit also includes 3-4 clutch piston return spring kit for the input drum which reduces centrifugal 3-4 clutch apply and failure in 1st gear at 5500 RPM or higher, transmission removal required if you want to fit this particular mod.

Corrects/Prevents/Reduces:
  • TCC slip or shudder
  • Code P1870 and P0894
  • Harsh 1-2 shift
  • Long soft shifts
  • Double bump or slide bump on the 1-2 shift
  • 2-3 flare up
  • 2-4 band failure
  • Burnt 3-4 clutch plates
  • Burnt forward and low/reverse clutch plates
  • Pump slide and valve bore wear
Includes:
  • Second servo piston spring, two shims and two O-rings
  • (2) 1-2 accumulator springs, spring seat and three spacers
  • 3-2 Downshift valve spring
  • Actuator feed limit valve spring
  • (2) 1-2 accumulator valve springs
  • USA-made hardened steel 1-2 shift valve and spacer
  • Low valve spring
  • USA-made hardened TCC regulator and isolator valve, spring and installation bolt
  • (2) Pressure regulator valve springs and spacer
  • .500” boost valve, bushing and snap ring
  • EPC screen wire spacer and oversized 1-2 checkball
  • (2) Drill bits
  • (2) Reverse input piston orifice cup plugs
  • 3-4 accumulator spring
  • (2) Valve body gaskets
  • Pan gasket
  • 3-4 clutch return springs and orifice capsule
  • Forward clutch return springs and installation washer



  ANY QUESTIONS, PLEASE ASK

IF YOU REQUIRE OTHER ANY OTHER PARTS, PLEASE MESSAGE US ON EBAY SO WE CAN LIST THEM