A paddle steamer is a steamship or steamboat powered by a steam engine that drives paddle wheels to propel the craft through the water. In antiquity, paddle wheelers followed the development of poles, oars and sails, where the first uses were wheelers driven by animals or humans.

Advance, a Greenock-built American Civil War blockade-running side-wheel steamer

In the early 19th century, paddle wheels were the predominant way of propulsion for steam-powered boats. In the late 19th century, paddle propulsion was largely superseded by the screw propeller and other marine propulsion systems that have a higher efficiency, especially in rough or open water. Paddle wheels continue to be used by small, pedal-powered paddle boats and by some ships that operate tourist voyages. The latter are often powered by diesel engines.[a]

Paddle wheels

Left: Riveted steel paddle wheel from a sidewheeler paddle steamer on the lake of Lucerne

Right: Detail of a steamer

The paddle wheel is a large steel framework wheel. The outer edge of the wheel is fitted with numerous, regularly spaced paddle blades (called floats or buckets). The bottom quarter or so of the wheel travels under water. An engine rotates the paddle wheel in the water to produce thrust, forward or backward as required. More advanced paddle-wheel designs feature "feathering" methods that keep each paddle blade closer to vertical while in the water to increase efficiency. The upper part of a paddle wheel is normally enclosed in a paddlebox to minimise splashing.

Types of paddle steamers

The Nettie Quill, pictured in Alabama in 1906, shows a typical early sternwheeler design.

The three types of paddle wheel steamer are stern-wheeler, with a single wheel on the rear, a side-wheeler with one on each side, and an inboard with the paddlewheel mounted in a recess amidship.[2] All were used as riverboats in the United States. Some still operate for tourists, for example on the Mississippi River.

Stern-wheeler

[icon]

This section needs expansion. You can help by adding to it. (October 2017)

Although the first stern-wheelers were invented in Europe, they saw the most service in North America, especially on the Mississippi River. Enterprise was built at Brownsville, Pennsylvania, in 1814 as an improvement over the less efficient side-wheelers. The second stern-wheeler built, Washington of 1816, had two decks and served as the prototype for all subsequent steamboats of the Mississippi, including those made famous in Mark Twain's book Life on the Mississippi.[3]

Side-wheeler

Old sidewheeler "Pittsburgh" in Gore Bay, Manitoulin Island

Side-wheelers are used as riverboats and as coastal craft. Though the side wheels and enclosing sponsons make them wider than stern-wheelers, they may be more maneuverable, since they can sometimes move the paddles at different speeds, and even in opposite directions. This extra maneuverability makes side-wheelers popular on the narrower, winding rivers of the Murray–Darling system in Australia, where a number still operate.

European side-wheelers, such as PS Waverley, connect the wheels with solid drive shafts that limit maneuverability and give the craft a wide turning radius. Some were built with paddle clutches that disengage one or both paddles so they can turn independently. However, wisdom gained from early experience with side-wheelers deemed that they be operated with clutches out, or as solid-shaft vessels. Crews noticed that as ships approached the dock, passengers moved to the side of the ship ready to disembark. The shift in weight, added to independent movements of the paddles, could lead to imbalance and potential capsizing. Paddle tugs were frequently operated with clutches in, as the lack of passengers aboard meant that independent paddle movement could be used safely and the added maneuverability exploited to the full.

Inboard paddlewheeler

Recessed or inboard paddlewheel boats were designed to ply narrow and snag infested backwaters. By recessing the wheel within the hull it was protected somewhat from damage. It was enclosed and could be spun at a high speed to provide acute maneuverability. Most were built with inclined steam cylinders mounted on both sides of the paddleshaft and timed 90Deg apart like a locomotive, making them instantly reversing.

Feathering paddle wheel

Morgan's feathering paddle wheel (Steam and the Steam Engine, Evers)

In a simple paddle wheel, where the paddles are fixed around the periphery, power is lost due to churning of the water as the paddles enter and leave the water surface. Ideally, the paddles should remain vertical while under water. This ideal can be approximated by use of levers and linkages connected to a fixed eccentric. The eccentric is fixed slightly forward of the main wheel centre. It is coupled to each paddle by a rod and lever. The geometry is designed such that the paddles are kept almost vertical for the short duration that they are in the water.[4]

History

Western world

Ox-powered Roman paddle wheel boat from a 15th-century copy of De Rebus Bellicis

The use of a paddle wheel in navigation appears for the first time in the mechanical treatise of the Roman engineer Vitruvius (De architectura, X 9.5–7), where he describes multigeared paddle wheels working as a ship odometer. The first mention of paddle wheels as a means of propulsion comes from the fourth– or fifth-century military treatise De Rebus Bellicis (chapter XVII), where the anonymous Roman author describes an ox-driven paddle-wheel warship:

Animal power, directed by the resources on ingenuity, drives with ease and swiftness, wherever utility summons it, a warship suitable for naval combats, which, because of its enormous size, human frailty as it were prevented from being operated by the hands of men. In its hull, or hollow interior, oxen, yoked in pairs to capstans, turn wheels attached to the sides of the ship; paddles, projecting above the circumference or curved surface of the wheels, beating the water with their strokes like oar-blades as the wheels revolve, work with an amazing and ingenious effect, their action producing rapid motion. This warship, moreover, because of its own bulk and because of the machinery working inside it, joins battle with such pounding force that it easily wrecks and destroys all enemy warships coming at close quarters.[5]

A 15th-century paddlewheel boat powered by crankshafts (Anonymous of the Hussite Wars)

Italian physician Guido da Vigevano (circa 1280–1349), planning for a new crusade, made illustrations for a paddle boat that was propelled by manually turned compound cranks.[6]

Paddle boat, by the Italian artist-engineer Taccola, De machinis (1449): The paddles wind a rope fixed to an anchor upstream, thus moving the boat against the current.

One of the drawings of the Anonymous Author of the Hussite Wars shows a boat with a pair of paddlewheels at each end turned by men operating compound cranks.[7] The concept was improved by the Italian Roberto Valturio in 1463, who devised a boat with five sets, where the parallel cranks are all joined to a single power source by one connecting rod, an idea adopted by his compatriot Francesco di Giorgio.[7]

In 1539, Spanish engineer Blasco de Garay received the support of Charles V to build ships equipped with manually-powered side paddle wheels. From 1539 to 1543, Garay built and launched five ships, the most famous being the modified Portuguese carrack La Trinidad, which surpassed a nearby galley in speed and maneuverability on June 17, 1543, in the harbor of Barcelona. The project, however, was discontinued.[8] 19th century writer Tomás González claimed to have found proof that at least some of these vessels were steam-powered, but this theory was discredited by the Spanish authorities. It has been proposed that González mistook a steam-powered desalinator created by Garay for a steam boiler.[8]

In 1704, French physicist Denis Papin constructed the first ship powered by his steam engine, mechanically linked to paddles. This made him the first to construct a steam-powered boat (or vehicle of any kind). Then, he poured the first steam cylinder of the world in the iron foundry at Veckerhagen.

In 1787, Patrick Miller of Dalswinton invented a double-hulled boat that was propelled on the Firth of Forth by men working a capstan that drove paddles on each side.[9]

Model made by de Jouffroy in 1784 to show the French Science Academy the engine and paddle wheels used on Pyroscaphe: The model is now in the National Maritime Museum in Paris.[10]

One of the first functioning steamships, Palmipède, which was also the first paddle steamer, was built in France in 1774 by Marquis Claude de Jouffroy and his colleagues. The 13 m (42 ft 8 in) steamer with rotating paddles sailed on the Doubs River in June and July 1776. In 1783, a new paddle steamer by de Jouffroy, Pyroscaphe, successfully steamed up the river Saône for 15 minutes before the engine failed. Bureaucracy and the French Revolution thwarted further progress by de Jouffroy.

The next successful attempt at a paddle-driven steam ship was by Scottish engineer William Symington, who suggested steam power to Patrick Miller of Dalswinton.[9] Experimental boats built in 1788 and 1789 worked successfully on Lochmaben Loch. In 1802, Symington built a barge-hauler, Charlotte Dundas, for the Forth and Clyde Canal Company. It successfully hauled two 70-ton barges almost 20 mi (32 km) in 6 hours against a strong headwind on test in 1802. Enthusiasm was high, but some directors of the company were concerned about the banks of the canal being damaged by the wash from a powered vessel, and no more were ordered.

While Charlotte Dundas was the first commercial paddle steamer and steamboat, the first commercial success was possibly Robert Fulton's Clermont in New York, which went into commercial service in 1807 between New York City and Albany. Many other paddle-equipped river boats followed all around the world; the first in Europe being PS Comet designed by Henry Bell which started a scheduled passenger service on the River Clyde in 1812.[11]

A paddle tug pulling HMS Temeraire to a breaking yard in 1838

In 1812, the first U.S. Mississippi River paddle steamer began operating out of New Orleans. By 1814, Captain Henry Shreve[b] had developed a "steamboat" [c] suitable for local conditions. Landings in New Orleans went from 21 in 1814 to 191 in 1819, and over 1,200 in 1833.

The first stern-wheeler was designed by Gerhard Moritz Roentgen from Rotterdam, and used between Antwerp and Ghent in 1827.[12]

Team boats, paddle boats driven by horses, were used for ferries the United States from the 1820s–1850s, as they were economical and did not incur licensing costs imposed by the steam navigation monopoly. In the 1850s, they were replaced by steamboats.[13]

After the American Civil War, as the expanding railroads took many passengers, the traffic became primarily bulk cargoes. The largest, and one of the last, paddle steamers on the Mississippi was the sternwheeler Sprague. Built in 1901, she pushed coal and petroleum until 1948.[14][15][16][17][18]

In Europe from the 1820s, paddle steamers were used to take tourists from the rapidly expanding industrial cities on river cruises, or to the newly established seaside resorts, where pleasure piers were built to allow passengers to disembark regardless of the state of the tide. Later, these paddle steamers were fitted with luxurious saloons in an effort to compete with the facilities available on the railways. Notable examples are the Thames steamers which took passengers from London to Southend-on-Sea and Margate, Clyde steamers that connected Glasgow with the resort of Rothsay and the Köln-Düsseldorfer cruise steamers on the River Rhine. Paddle steamer services continued into the mid-20th century, when ownership of motor cars finally made them obsolete except for a few heritage examples.[19]

China

A Chinese paddle-wheel ship from a Qing dynasty encyclopedia published in 1726

The first mention of a paddle-wheel ship from China is in the History of the Southern Dynasties, compiled in the 7th century but describing the naval ships of the Liu Song dynasty (420–479) used by admiral Wang Zhen'e in his campaign against the Qiang in 418 AD. The ancient Chinese mathematician and astronomer Zu Chongzhi (429–500) had a paddle-wheel ship built on the Xinting River (south of Nanjing) known as the "thousand league boat".[20] When campaigning against Hou Jing in 552, the Liang dynasty (502–557) admiral Xu Shipu employed paddle-wheel boats called "water-wheel boats". At the siege of Liyang in 573, the admiral Huang Faqiu employed foot-treadle powered paddle-wheel boats. A successful paddle-wheel warship design was made in China by Prince Li Gao in 784 AD, during an imperial examination of the provinces by the Tang dynasty (618–907) emperor.[21] The Chinese Song dynasty (960–1279) issued the construction of many paddle-wheel ships for its standing navy, and according to the British biochemist, historian, and sinologist Joseph Needham:

"...between 1132 and 1183 (AD) a great number of treadmill-operated paddle-wheel craft, large and small, were built, including sternwheelers and ships with as many as 11 paddle-wheels a side,".[22]

The standard Chinese term "wheel ship" was used by the Song period, whereas a litany of colorful terms were used to describe it beforehand. In the 12th century, the Song government used paddle-wheel ships en masse to defeat opposing armies of pirates armed with their own paddle-wheel ships. At the Battle of Caishi in 1161, paddle-wheelers were also used with great success against the Jin dynasty (1115–1234) navy.[23] The Chinese used the paddle-wheel ship even during the First Opium War (1839–1842) and for transport around the Pearl River during the early 20th century.

Seagoing paddle steamers

PS Waverley, the last seagoing paddle steamer

The first seagoing trip of a paddle steamer was by the Albany in 1808. It steamed from the Hudson River along the coast to the Delaware River. This was purely for the purpose of moving a river-boat to a new market, but paddle-steamers began regular short coastal trips soon after. In 1816 Pierre Andriel, a French businessman, bought in London the 15 hp (11 kW) paddle steamer Margery (later renamed Elise) and made an eventful London-Le Havre-Paris crossing, encountering heavy weather on the way. He later operated his ship as a river packet on the Seine, between Paris and Le Havre.

The first paddle-steamer to make a long ocean voyage crossing the Atlantic Ocean was SS Savannah, built in 1819 expressly for this service. Savannah set out for Liverpool on May 22, 1819, sighting Ireland after 23 days at sea. This was the first powered crossing of the Atlantic, although Savannah was built as a sailing ship with a steam auxiliary; she also carried a full rig of sail for when winds were favorable, being unable to complete the voyage under power alone. In 1822, Charles Napier's Aaron Manby, the world's first iron ship, made the first direct steam crossing from London to Paris and the first seagoing voyage by an iron ship.

One of Commodore Perry's fleet: either Mississippi or Susquehanna

In 1838, Sirius, a fairly small steam packet built for the Cork to London route, became the first vessel to cross the Atlantic under sustained steam power, beating Isambard Kingdom Brunel's much larger Great Western by a day. Great Western, however, was actually built for the transatlantic trade, and so had sufficient coal for the passage; Sirius had to burn furniture and other items after running out of coal.[24] Great Western's more successful crossing began the regular sailing of powered vessels across the Atlantic. Beaver was the first coastal steamship to operate in the Pacific Northwest of North America. Paddle steamers helped open Japan to the Western World in the mid-19th century.

The largest paddle-steamer ever built was Brunel's Great Eastern, but it also had screw propulsion and sail rigging. It was 692 ft (211 m) long and weighed 32,000 tons, its paddlewheels being 56 ft (17 m) in diameter.

In oceangoing service, paddle steamers became much less useful after the invention of the screw propeller, but they remained in use in coastal service and as river tugboats, thanks to their shallow draught and good maneuverability.

The last crossing of the Atlantic by paddle steamer began on September 18, 1969, the first leg of a journey to conclude six months and nine days later. The steam paddle tug Eppleton Hall was never intended for oceangoing service, but nevertheless was steamed from Newcastle to San Francisco. As the voyage was intended to be completed under power, the tug was rigged as steam propelled with a sail auxiliary. The transatlantic stage of the voyage was completed exactly 150 years after the voyage of Savannah.

As of 2022, the PS Waverley is the last seagoing passenger-carrying paddle steamer in the world.

Paddle-driven steam warships

Paddle frigates

Main article: Paddle frigate

Matthew C. Perry's paddle frigate USS Mississippi, part of the Black Ships expedition to Japan (1853–1854)

Beginning in the 1820s, the British Royal Navy began building paddle-driven steam frigates and steam sloops. By 1850 these had become obsolete due to the development of the propeller – which was more efficient and less vulnerable to cannon fire. One of the first screw-driven warships, HMS Rattler (1843), demonstrated her superiority over paddle steamers during numerous trials, including one in 1845 where she pulled a paddle-driven sister ship backwards in a tug of war.[25] However, paddle warships were used extensively by the Russian Navy during the Crimean War of 1853–1856, and by the United States Navy during the Mexican War of 1846–1848 and the American Civil War of 1861–1865. With the arrival of ironclad battleships from the late 1850s, the last remaining paddle frigates were decommissioned and sold into merchant-navy service by the 1870s. These included Miami, which became one of the first Boston steamers in 1867.[26]

Paddle minesweepers

HMS Plumpton, a British paddle minesweeper built in 1916.

At the start of the First World War, the Royal Navy requisitioned more than fifty pleasure paddle steamers for use as auxiliary minesweepers.[27] The large spaces on their decks intended for promenading passengers proved to be ideal for handling the minesweeping booms and cables, and the paddles allowed them to operate in coastal shallows and estuaries. These were so successful that a new class of paddle ships, the Racecourse-class minesweepers, were ordered and 32 of them were built before the end of the war.[28]

In the Second World War, some thirty pleasure paddle steamers were again requisitioned;[27] an added advantage was that their wooden hulls did not activate the new magnetic mines. The paddle ships formed six minesweeping flotillas, based at ports around the British coast. Other paddle steamers were converted to anti-aircraft ships. More than twenty paddle steamers were used as emergency troop transports during the Dunkirk Evacuation in 1940,[27] where they were able to get close inshore to embark directly from the beach.[29] One example was PS Medway Queen, which saved an estimated 7,000 men over the nine days of the evacuation, and claimed to have shot down three German aircraft.[30] Another paddle minesweeper, HMS Oriole, was deliberately beached twice to allow soldiers to cross to other vessels