Archgard FK-38 Fireplace Blower Fan Kit for Marquis 38
Aftermarket FK-38 fan kit for the Archgard Marquis 38. Replaces the original tangential (squirrel cage) style blower for a more powerful 180CFM dual centrifugal model. Kit is also paired with the OEM style thermostat sensor and speed controller.
FK-38 Blower Kit Installation
- Disconnect the power before stripping or joining any supply wires. Only qualified persons should attempt to make incoming supply wire connections.
- Remove the lower louver by lifting up and out
- Install the fan first. Gently slide right end of the fan into the bottom left side of the gas fireplace. Rotate the fan as it passes by the aluminum gas line. Position blower at center of rear wall and leave blower 1/8" off the rear wall to avoid any metal on metal contact
- Run 120VAC power line through the wire clamp on the left side of the fireplace and into the bottom of the gas fireplace. Connect a grounding wire to the side of gas fireplace. A screw hole is provided for this purpose. Connect the two bare ended wires from the speed controller assembly to the power line. See Wiring Diagram.
- Slide the thermal snap switch into the “U” clip located underneath the firebox bottom at the left front corner.
- Neatly tie down and tuck the wires down at the bottom and to the back of the fireplace. CAUTION: Do not allow any wires to touch the bottom of the firebox. Otherwise, the wires will melt and short-out.
- Remove the speed controller knob. Using the two black screws, screw the speed controller bracket to the bottom left sidewall of the gas fireplace. Make sure there are no wires exposed at the front. Replace the knob.
- Tighten the wire clamp. Replace the lower louver.
Benefits of Adding a Fireplace Blower
- Improves fireplace efficiency by as much as 80%
- Helps reduce costly energy bills
- Heats large rooms effectively
- Installs quickly and easily
- Affordable and efficient
Included With Purchase
- 180 CFM ball bearing blower assembly
- Pre-wired for easy installation
- Rheostat variable speed controller
- Automatic thermostat sensor
- Rubber isolation feet for noise reduction
- Heavy duty grounded 3 prong power cord
- 3 to 2 prong outlet adapter
- Installation instructions
- 1 year warranty
Product Details
|
Specifications
|
|
|---|---|
| Dimensions | |
| L x W x H | 12.8" x 4.0" x 4.0", removing rubber feet drops height below 4" when blower is slightly rotated. Flange height of air discharge sits 1/16" taller than the 4", but does not cause clearance issues. |
| Air Discharge | 4.75" each blower |
| Blower, Motor & Bearing | |
| Type | AC Shaded Pole |
| Rotation | CW/CCW |
| Blade Type | High temperature rated composite |
| Housing Material | Steel powder coated black |
| Bearing Type | Ball |
| Outboard Bearing Type | N/A |
| Bearing Lubrication | High Temp |
| Motor Insulation | Class H (rated to 392°F) |
| Motor RPM | 3000 |
| Air Flow | |
| CFM | 180 CFM |
| Installation | |
| Mounting Type | Free standing, bracket has 4 rubber grommets that are attached to bracket and can be used to secure blower with hardware if needed. |
| Electrical | |
| Volts | 115 |
| Motor Frequency | 60 Hz |
| Watts | 184 |
| Amperage | 1.60 |
| Power Cord | Yes |
| Power Cord Length | 3 ft |
| Power Cord Type | 3-prong grounded |
| Accessories | |
| Rheostat Variable Speed Controller | Yes. Inline thermostat is included, which mounts below the fireplace. A wall mount version is available as an option. |
| Thermostat | Yes |
| Thermostat Type | Selco snap style 3/4" |
| Thermostat Temperature | 120° / 90° |
| Other | |
| Packaging Materials | Shipping box, bubble wrap, foam |
| Compatibility | |
| Archgard | Marquis 38 (AGDV-38D, AGDV-38DP) |
| Documents | |
| Installation Instructions | See above |
| Comparison | Watch Now |
Also Known As
- FK-38
