- 16MB Flash and 8M PSRAM
- Note:SIM7000G does not support 4G network. Please ensure that the USIM card you use supports 2G(GSM)/NB-IOT access
- Peripheral Interfaces: I2C , SPI , UART , SDIO , I2S , CAN
- More information:github.com/Xinyuan-LilyGO/LilyGO-T-SIM7000G
- If you have any questions about our products, please feel free to
Product Description
Product Pin
- About the onboard indicator light description:
- In the pin diagram, the red indicator light near the upper right of the switch is only on when the battery is connected, and it is always on when the USB is connected. It indicates that the battery is charging. If the battery is not connected, it may be Flashing.
- Below the red light is the green indicator light, which lights up only when the battery is fully charged, and it is always on when the battery is connected.
- Close to the side of the SIM7000G antenna is the status indicator. If the SIM7000G starts normally, it will always be on. If it does not start normally, it will not be on. It cannot be turned off by software.
- Close to the status indicator is the network indicator, it indicates the network status, it can be closed by software.
Product Function :
- The battery's positive and negative poles are connected to the wrong protection, overcharge and over discharge protection
- GPS power control, reduce power consumption, the lowest reaches 300uA when sleeping
- of ordinary charging IC with solar charging IC
- Added active GPS antenna power control, when the module GPIO4 is not turned on the antenna consumes only the static current of the LDO
For more information and manuals, please check Github :github.com/Xinyuan-LilyGO/LilyGO-T-SIM7000G
Notes for new Users
- SIM7000G does not support 4G network. Please ensure that the USIM card you use supports 2G(GSM)/NB-IOT access.
- pin VIN is a USB input, if a battery is being used to power the device there will be no voltage output from VIN meaning 3.3v is the only power output.
- When using the built-in battery pack the on/off switch will function as normal, supplying/cutting off power to the board, However, if an external battery pack is used and attached to the VBAT pin the on/off switch will be bypassed meaning the only way to shut off will be to disconnect the batteries.
- On/off switch is for battery use only, it will not function when plugged into USB.
- Battery voltage can not be read when plugged into USB using the onboard BAT ADC(35)
- Recommended solar panels are 4.4v to 6v DO NOT EXCEED OR BOARD MAY BE DAMAGED
Product Description
Power MCU:ESP32 Clock Speed:240Mhz Wireless Connectivity : Wi-Fi: 802.11 b/g/n Bluetooth: v4.2 BR/EDR and BLE Peripheral Interfaces: 12C、 SPI、 UART、SDIO、12S、CAN | Antenna Data Transfer: Cat-M (Kbps):300(DL)/375(UL) Cat-NB(Kbps):34(DL)/66(UL) EGPRS( Kbps ):85.6(DL)/85.6(UL) Supply Voltage(V):3.0~4.3 SIM Card:1.8V | Shipping List 1x T-SIM7000G 1x SIM antenna 1x GPS antenna 1x Power cable 2x Pin |
Software Features :
FOTA、Embedded AT、 Firmware Upgrade
Power Consumption :
PSM(uA):9 , Sleep(mA):1, ldle(mA):II
Frequency Bands:
Cat-M : B1/B2/B3/B4/B5/B8/B12/B13/B17/
B18/B19/B20/B25/B26/B28/B39
Cat-NB : B1/B2/B3/B4/B5/B8/B12/B13/B17/ B18/B19/ B20/B25/B26/B28
- REGION : G:Global
- Form Factor : LCC,68PIN
- Interface : UART、USB、PCM、ADC、I2C
- GNSS:BeiDou、GPS、GLONASS
- Protocol:TCP/UDP/LWM2M/COAP/NTP/MQTT/FTP/HTTP/TLS/DTLS
-
Item model number |
T-SIM7000G |
RAM |
psram |
Series |
CH9102F 16MB |
Ram Memory Installed Size |
16 MB |
Wireless Type |
Bluetooth, 802.11b |
Item Weight |
2.89 ounces |
Connectivity Technology |
Bluetooth, Wi-Fi, I2C |
Model Name |
CH9102F 16MB |
Memory Storage Capacity |
16 MB |
Package Dimensions |
6.14 x 4.8 x 1.5 inches |
Manufacturer |
® |