WOODPECKER LED.B:
Feature:
100% guaranteed original Woodpecker. Each item has unique serial number, which indicate in which region it is supposed to be sold. Woodpecker is strict with that regulation of according regional sale. As ours are to be sold in China only, we have to erase it from item, which would cause scratch-like mark. That is no damage, pls note this clearly!

Wireless.
Time setting: 5s, 10s, 15s, 20s.
Large capacity battery. A full charge can be used for more than 500 times continuously under 10s working time mode.
Low standby power consumption with seventy days` standby time.
Constant light intensity. The solidification effect is not affected by the consumption of remaining power.

Technical Parameter
Power input: AC100V-240V 50Hz/60Hz
Light output: 1000mW/cm² -1200mW/cm²
Net weight: 145g
Dimensions: 260mm×31mm×34mm

LED B Packing List
1 X Curing light
1 X High capacitance rechargeable battery
1 X Charger
1 X Charger socket

 *******************************************************************************************************

 

LED D

 

Wireless.
The battery can be replaced.
Three working modes: Full, Ramping, Pulse.
Time setting: 5s, 10s, 15s, 20s, 25s, 30s, 35s, 40s.
A full charge can be used for over 400 times. (10s/time)
Constant light intensity, the solidification effect is not affected by the consumption of remaining power.
With wire or wireless. It can run directly on commercial power supply whilst the battery runs out.
Technical Details:
Power input AC100V-240V 50Hz/60Hz
Light output 850mW/cm² - 1000mW/cm²
Net weight 143g
Dimensions 264mm × 32mm × 37mm
Packing List:
1 X Curing light
1 X High capacitance rechargeable battery
1 X Charger
1* Curing light holder
 
 *******************************************************************************************************
 
WOODPECKER I LED Plus (Radom Color):

Brand: Woodpecker

100% original promise !
Wide spectrum, High light intensity, Focused light
Constant power output, born for teeth restoration
360° curing, reach every angle
Fluid design, better hand feeling
Upgraded light intensity
Two modes for option
With the maximum light intensity of 2300mw/cm2
curing 2mm resin in 1 second
Which makes it especially suitable for orthodontic brackets, porcelain verneers and post-core adhensives.

Technical parameter
1. Light output: 1000 mW/cm2 ~2500mW/cm2
2. Wave length: 385nm-515nm
3. 360° rotatable head
4. 1 sec for curing
5. Time setting:
Turbo (P1)-1s, 3s ,2300~2500 mw/cm²
Normal (P2)-5s, 10s, 15s, 20s,1000~1200mw/cm²

Dimensions: 25mm×25mm×240mm
Net weight: 278g
Power Input: 100V to 240V, 50Hz/60 Hz
Wave length: 385nm-515nm
Light intensity：1000mW/cm²-2300mW/cm²
 
 *******************************************************************************************************
 
LY-A180:

Classic rechargeable light curing unit: Environmental colorful plastic shell; Lotus charging pedestal; Handle can be placed horizontally / upright, to ensure that the light guide stick is not easy to break; 5W high power LED; High permeability rate of glass fiber-optic, strong, flashing, gradually strong 3 modes, large capacity lithium battery, automatic standby/shutdown, low battery warning, suitable for all brands of resin materials; long standby time of 90 days or more. Be charged one time, in accordance with each working time of 20 seconds, it can be used continuously for more than 130 times.

Operating mode diagram:
1. Power switch
2. Low battery alert
3. Strong mode indicator light
4. Flashing mode indicator light
5. Gradually strong mode indicator light
6. Mode select switch
7. Be adjusted in 5-40 seconds, shut down automatically . Without any operation in 20 seconds.

Technical data:
Package: 190×98×60m
Suitable temperature: 5℃~50℃
Solidify time and depth: 5s/3mm
Light wavelength: 420-480nm
Light intensity: 1200-2000mw/cm2
Gross Weight: 0.30Kg
Input Voltage: 110V-240VAC, 50-60Hz
Output Voltage: DC 4.2V
Battery: Lithium-ion battery
Capability of Battery: 2200mA

 ******************************************************************************************************* 
 
DENTMAX LED.B:
Feature:
100% guaranteed original DENTMAX. 

Wireless.
Time setting: 5s, 10s, 15s, 20s.
Large capacity battery. A full charge can be used for more than 500 times continuously under 10s working time mode.
Low standby power consumption with seventy days` standby time.
Constant light intensity. The solidification effect is not affected by the consumption of remaining power.

Technical Parameter
Power input: AC100V-240V 50Hz/60Hz
Light output: 1000mW/cm² -1200mW/cm²
Net weight: 145g
Dimensions: 260mm×31mm×34mm

LED B Packing List
1 X Curing light
1 X High capacitance rechargeable battery
1 X Charger
1 X Charger socket

********************************************************************************************************
Xlite2 neo:
Light Source: Broad Band LED;
Wavelength Range: 385 - 515 nm;
Light Intensity: > 2300mW/cm²;
Battery: Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);
Power Adapter Input Power: AC 100-240V 50 / 60Hz;
Charging time: about 45 minutes.
Size:Handle: Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm(all of the above are the largest size)
Weight: Handle: 96 grams; Charging seat: 99 grams;
Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F);
Operating relative humidity: 30% - 75%;
Operating environment pressure: 700hPa - 1060hPa;
Color Choose: White/ Black （Radomly color）

Package Contents:
1 × host handle;
1 × charging base;
1 × power adapter;
1 × user manual.

Operation and function description:
The entire handle is only one button, light built-in button.
1. For the first time, charge the light curing handle first. Plug the USB
2. cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally
Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put
the handle on the charging stand. Charging instructions are as follows:
| Emerald Flashing | Battery charging;
| Emerald green light | battery fully charged; handle removed the
charging seat, the restoration of the previous working mode.
3. Working mode selection, by pressing the button for 2 seconds to
4. release to switch the working mode.
| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW/cm².
| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²
3. Turn the light curing lamp on and off, press the button briefly.
4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby.

Package including: 1 Set ( radomly color)

********************************************************************************************************
 
DMX iLED Ⅱ(White/Black Optional):
Feature: 
Light Source: Broad Band LED;

Wavelength Range: 385 - 515 nm;

Light Intensity: > 2300mW/cm²;

Battery: Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);

Power Adapter Input Power: AC 100-240V 50 / 60Hz;

Charging time: about 45 minutes.

Size:Handle: Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm(all of the above are the largest size)

Weight: Handle: 96 grams; Charging seat: 99 grams;

Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F);

Operating relative humidity: 30% - 75%;

Operating environment pressure: 700hPa - 1060hPa;

Color Choose: White/ Black （choose the color you like）

Package Contents:

1 × host handle;

1 × charging base;

1 × power adapter;

1 × user manual.

Operation and function description:

The entire handle is only one button, light built-in button.

1. For the first time, charge the light curing handle first. Plug the USB

2. cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally

Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put

the handle on the charging stand. Charging instructions are as follows:

| Emerald Flashing | Battery charging;

| Emerald green light | battery fully charged; handle removed the

charging seat, the restoration of the previous working mode.

3. Working mode selection, by pressing the button for 2 seconds to

4. release to switch the working mode.

| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW/cm².

| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²

3. Turn the light curing lamp on and off, press the button briefly.

4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby.
 
 *******************************************************************************************************
2001B:
Specifications:
Light Density ≥2700mW/cm
Battery ：3500mAH                
Input Voltage :AC100-240      
Power:  12W                
Wavelength：400nm - 490nm

Features:
1. Lithium battery
2. Pure LED blue light and no flicker        
3. Aluminium body
4. 3 second can make it! (selection from 2-6 seconds)

Package：
1. Light guide           
2. Circular eye-protector
3. power adapter        
4. Charging base
5. Main body    
6. Manual  
 
 
 *******************************************************************************************************
 
DMX iLED:
1.INTRODUCTION
This product is used in fast solidification by lighting dental resin. It is a new generation of standard developed LED curing light, with humanity intelligent chip, the world advanced high intensity LED light and Li-on rechargeable battery. It can cure all the dental resin in the market nowadays,
 
2.PACKING LIST
Main Body: 1Pc             Light Source:: 1Pc
Charge Base: 1Pc          Adapter: 1Pc
USB cable: 1Pc               Light Protect: 1Pc
Lens: 5pcs                     Test block:2pcs
 
3.TECHNICALPARAMETERS
3.1 Main Unit
 
Battery Voltage DC3.7V
Battery Capacity 1500mAh
Wave Length 385～515nm
Light Density P1(9W) ≥ 2300mmw/cm²
P2（5W）≥1200mw/cm²
Charging time 3 hours approx
Weight 550g
Packing size L205 x W109 x H77mm
 
3.2AC Adapter
Rated input voltage AC100-240V 50/60Hz
Output voltage DC 5V/MICRO USB
Output current 1A
 
3.3 Operation Conditions
 
Environment temperature +5 ℃ ~+40 ℃
Relative humidity 10%~80%RH
Atmospheric pressure 50~106KPa

4.Use Method
4.1 Charge
Put the curing light into the charger base, the blue light is shining one by one. When it is done, all of the blue lights are on.It takes about 3hours. Take care not to charge more than 7hours. Remove the adapter from the power supply after charging.
Note: Can charge with the main unit socket also. When charging, theLED screen show CH; when done, the LED show FU

4.2 Operation Instruction
4.2.1Press M orTbutton to power on.Ifpress ON/OFF button, will light the Light source.
4.2.2 Set up Mode:

P1(9W,≥2300mw/cm²) The actual measured value 2800mw/cm²
P2（5W，≥1200mw/cm²）
 
4.2.3 Setup Time:P1--1/3/5s
                        P2--6/10/15/20s
4.2.4Press ON/OFF button to light on the LED curing light. Ifsome wrong happened, the LED screen shows Er.
4.2.5 The main unit will power off by itselfif without any operation about 2minuts.
 
Caution: the curing light can not be pointed at the patient's eyes while it is operating. If any accidents happen, go to the hospital immediately
 
5.Precautions
5.1 This machine is precise opticalequipment,it should use in the clean and dry place.
5.2 Remove adapter from the power supply after charge. 5.3 Do not touch the battery electrodes by any metal objects.
6.Cleaning & Sterilization
6.1 Clean
Wipe the main unit with neutral detergent if needed.

6.2 Sterilization
6.2.1 The light source can be high pressure autoclaved. Autoclave it after each use with seal bag.
6.2.2Don't autoclave any parts(the main unit and charging base)other than those that can be subjected to autoclave sterilization.
6.2.3 Autoclave up to a max.135℃. It's recommended to autoclave for 20min at 121℃ or 15 min at 132℃.
Notice: Don't use any solvent such as benzine and thinner for sterilization.
7.Transportation And Storage
1)Lay lightly during transportation, avoid strong shake 2) Storage condition:
a. Ambiance temperature:-10~～40℃b.Relative humidity:≤85%
8.Disposing product
Please consult with dealer from whom you purchased it about waster despoil.
9.Warranty
Manufacturer warrants its products to the original purchaser against defects in material and workmanship under normal practices of installation, use and servicing. This unit is guaranteed for its designated use against original defects in materials and workmanship for a period of 12 months from date of purchasing.
 
 *******************************************************************************************************
 
LY-C240:
Feature:
1.Super 10W high power LED bulb.
2.360° rotating light source, 90° right angle illumination.
3.The 3 mm resin can be cured by strong light for 1 second, and the light intensity is greater than 2000 mw/cm2
4.The outer casing is made of environmentally friendly plastic material, which is beautiful and practical.
5.Strong light, pulse, fade-on three working mode selection, 1~40 seconds working time.

Parameters:
Packing specification:10.25*6.5*2.56in
Net Weight:26.1 oz
Gross Weight:28.2oz
Output voltage:110v-220VAC, 50-60HZ
Output voltage:DC5V
Battery: Lithium ion battery
Capability of battery:2200mah
Battery voltage:3.7V
Suitable temperature:5°~50°C
Relative humidity:≤80%
Solidify time and depth:1s/3mm
Light wavelength:420-480nm
Light intensity:1200-2500 mw/cm2

Package Included:
Subject*1
Power adapter*1
Charging base*1
Instruction manual*1
 
********************************************************************************************************
 
MAXCURE9 (Radom Color) :
Features:
Power Input: 100-240VAC 50Hz/60Hz
Power Output: 5V DC/1A
Wave length: 385nm-515nm
Light intensity: 1000mW/cm2–  2500mW/cm2
Battery: 2600mA

Description
Light cure unit is used for the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time, it is used to restore teeth and solidify material for whitening teeth.

Indication
Used for polymerization of light cure resin-based composites. It can be used on several different dental materials that are curable by light.

Feature
1.Dual intensity mode
P1 High intensity mode
Curing time For orthodontic brackets, post and core and curing photosensitive adhesive in porcelain veneer.
High intensity mode
Constant intensity: 2300-2500mw/cm Used for quick curing, ensuring enough curing depth, more efficient
Time setting: 1s. 3s

P2 General intensity mode
Curing time For Normal resin.
General mode Constant intensity: 1000-1200mw/cm for most treatment scenarios like teeth filling, restoration etc.
Time setting: 5s, 10s. 15s, 20s

2.Broad-spectrum curing most materials
Most of the resins on the market use CQ as the photoinitiator, but some resins use two new types of photoinitiators, dipheny phosphorus oxide or Ivocerin, cnd the new materials containing TPO have a light bsorption peak of 405nm. If you use an crdinary narrow-spectrum light curing machine (wavelength range: 420nm-480nm), the resin is prane to incomplete curing. And we know that incomplete composite curing often leads to secondary pulpitis, apical inflammation, and tooth hypersensitivity.
MaxCure 9 broad-spectrum light curing, newly added the 385-420nm band, the wavelength range is 385nm-515nm. It can better cure resin materials containing TPO and other emerging photoinitiators, and is suitable for ideal curing of all resin materials on the market.
After a full upgrade, MaxCure 9 changes from a single blue light to a blue-violet light, which can truly cure all light-curing materials.

3.Super large battery capacity
2600mAh lithiurn battery- International CB certification
MaxCure9 Battery capocity is 85% higher than normal Curing Lights

4.Constant Current Driver
Constant light intensity. Constant light intensity output, stabilizing the working power

5.Light guide automatic detection
The main unit will detect the light guide and stop the "Er" flashing if the guide is connected well, or the main unit will close down after 10s flashing.
Well-installed during the period of the error alarm will stop the error alarm and the lamp will light up instantly when the lamp holder is installed.

6.Overheating protection
Main unit will detect the temperature. The overheating protection program will run when the curing light reaches a certain temperature after long time use. It' Il keep flashing until 200s later that it recovers from high-temperature.

7.Battery performance detection
When detect an inconstant power output from battery, the main unit will stop working to warn with flashing "Er".

8.Overvoltage protection
With overvoltage adapter, MaxCure 9 is under protection and can' t be charged. The original adapter is recommended.

Technical Specification:
Humidity 10%-93%
Atmosphere pressure 70kPa-106kPa
Temperature -20°C - + 40°C
Light power more than 2000mw/cm².
3 Distinct Modes: Strong, Flashing, Gradually strong.
2600 mAh Large-capacity lithium battery.
5W Big power LED.
Full charging available use more than 200 times.
Automatic Standby/Automatic shutdown.

CHARGING INDICATION:
The light is on when the machine is in charging mode.

Packaging:
1 x Light Cure Unit
1 x Adapter
1 x Charging Station
100 x Disposable PE isolation sleeves
1 x Instructions Manual
 
 *******************************************************************************************************
 
LY B200-B:
Cure Light covered by ABS painting
5W big power LED Cure Light
High articulation optical fiber
Cure Lamp Working models:strong
Automatic standby and shut down
Low Battery alert
Large-capacity lithium battery
Wireless curing lamp Solidify all brands of resin materials
 
Technology data:
Capacity of battery:2200mA/h3.7v
Working voltage : AC100-240V 50-60Hz
Wavelength: 420-480 nm
Light power: more than 1500mw/cm2
Solidification time and depth: 5s/3mm
 
 *******************************************************************************************************
 
Guide Rod Tips(free choose):
100% brand new and high quality
8mm diameter for tube
12mm diameter * 15mm/22mm length for metal parts

Model available：
Optical Fiber Guide Rod Tips（8*12*22）
Optical Fiber Guide Rod Tips（8*12*15）
 

********************************************************************************************************
 
Guide Protective Sleeves:
NOTICE: Curing Light Lamp Guide Rod NOT INCLUDED
Size: 20mm*82mm
Package: 200 pcs per box
 
********************************************************************************************************
Led Light Meter:
Feature:
LED Light Meter:
Using a light guide, center the light source over the detector window read the useful curing power in mw/c㎡
Used to test the curing power of dental curing light etc.
Interpreting the results:
Under 300: Indicates low output
300-500: Test composite to determine curing time
500-800: Use recommended during time appropriately
Over 800: High output-reduce curing time appropriately.  

 *******************************************************************************************************

LED Whitening Tip 12*15mm

- Fits for curing light

- The bottom of the tip is 12mm

Specification:- Material: High Quality Plastic
- Color: Transperant
- Size: 12x15mm / 0.47x0.59 inch

Package Includes:

1x Teeth Whitening Tip

 *******************************************************************************************************                                    

Wavelength：440-480nm

Light power：5W

Intensity：800-1400mw/cm²

Battery：Li-on 800mAh

Input voltage：AC100-240V, 50/60Hz 0.4A Max

Output voltage：DC 5V/1.5A

Net Weight：155g

Mode selection：P1, P2, P3

Solidification time：1S,3S,5S,10S,15S,20S

 Features:

·Produce the maximum light intensity safely.

· A high intensity of 1400 mW/cm2.

· Offers extremely short curing times of no more than 3 seconds.

· Cordless, highly portable and light weight (only 155g).

· High-performance Li-ion battery technology.

· LED panel conveniently indicates a countdown curing time.

· Battery can be fully recharged in 90 minutes.

· Battery with protection against over-voltage, over-current and short circuit.

· 3 versatile curing modes for every indications.

· Automatic power off, low battery alert.

· Color : White . 

Operation conditions:

Storage Condition: Temperature: +10℃+40℃
Humidity: 30%-75%
Atmospheric pressure: 70KPa-106Kpa
Environment Conditions: Not near from fire equipment or flammability material.
Packing list:  

The host       * 1                  

Metal lamp holder *1

The silicone base  *1

Power adapter     *1

Disposable protective sleeve  *1

Shade plate  *1

Product specification   *1           

 ******************************************************************************************************

 

Using a light guide, center the light source over the detector window read the useful curing power in mw/c㎡
Used to test the curing power of dental curing light etc.
Measures useful curing energy up to 3500 mW/cm2

100% Woodpecker original
Brand: Woodpecker
Model: LM-1

Features:
light, compact design
capable of measuring both LED and halogen curing lights.
Able to measure intensity up to 3500mw/cm2