|
2
Channel 2000M Normally Open/Closed DC Toggle RF
Remote Control ON/OFF Switch |
|
Model: 0020270 |
|
This 2
channel dc rf
remote control
on off switch is
great for hard
to reach lights
or other DC/AC
electrical
devices, remote
distance up to
2000m. You can
use it to
control two same
or different
electrical
devices. For
example, turn on
/ off the light
or (and) open /
close the door.
Applications
include light
remote control,
electric gate
remote control,
electric window
/ blind remote
control, etc.
Package
Include:
-
1 x Receiver: S2T-DC09-ANT2 / S2T-DC12-ANT2 /
S2T-DC24-ANT2 (2 Channels / Toggle Control Mode)
-
1 x Transmitter: CB-2
-
1 x User manual
Feature:
-
Application: It can be used in industry
automation, agriculture automation and home automation, such as factory, house,
farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call,
etc. It can remote control equipments on land, water and air, such as remote
control lights, sirens, locks, motors, fans, winches, blinds, linear actuators,
doors, windows, electric solenoid valves, security alarm, business signs and
various devices.
-
Wireless control, easy to install.
-
Relay Output: This receiver is relay output,
it can be used to operate both DC and AC equipments. The terminals are NO / NC
(normally open / normally closed), which serves as a switch. That means you
should also connect a separate power supply to equipments.
-
You can turn on/ off the receiver with
transmitter (remote control) from any place within a reliable distance.
-
Wireless RF signal can pass through walls,
floors, doors or windows.
-
With reverse power protection and over current
protection.
-
Reliable control: The receiver only works with
the transmitter which use same code.
-
One/several transmitters can control
one/several receivers simultaneously.
-
You can use two or more units in the same
place.
Receiver:
-
Model No.: S2T-DC06-ANT2 / S2T-DC09-ANT2 / S2T-DC12-ANT2 /
S2T-DC24-ANT2
-
Power Supply (Operating
Voltage): DC6V (S2T-DC06-ANT2), DC12V±1V (S2T-DC12-ANT2), DC9V±1V
(S2T-DC09-ANT2), DC24V±1V (S2T-DC24-ANT2)
-
Output: Relay output (Normally open and normally closed)
-
Working Voltage Range of
Relay: AC110~240V or DC0~28V
-
Working Frequency: 315MHz
/ 433MHz
-
Channel: 2 CH
-
Control Modes: Toggle (Press -> On; Press again -> Off)
-
Static Current: ≤6mA
-
Maximum Working Current:
10A / each channel
-
PCB size: 67mm x 50mm x 18mm
-
Case size: 75mm x 54mm x 27mm
-
Work with Fixed code transmitters or Learning code transmitters.
Transmitter:
-
Model No.: 0021024 (CB-2)
-
Channel/Button: 2
-
Button Symbol: big button, small button
-
Operating Voltage: 9V (1
x 6F22 -9V battery, can be used for 12 months)
-
Operating Current: 30mA
-
Operating Frequency:
315Mhz / 433Mhz
-
Encoding Chip: PT2262 / PT2264 / SC2262
-
Encoding Type: Fixed code by soldering, up to 6561 codes
-
Transmitting Distance:
1000m / 3000ft (theoretically)
-
The distance of 1000m is a theoretical data, it shall be operated
in an open ground, no barriers, no any interference. But in the practice, it
will be hindered by trees, walls or other constructions, and will be exposed to
some interference by other signals. Therefore, the actual distance may or may
not reach 1000m.
-
If you stretches the telescopic antenna, it can have a further
working range, which is twice as much as it used to be.
-
Modulation Mode: ASK
-
Operating Temperature: -20 ° C to +70 ° C
-
Unit Size: 135mm x 42mm x 25mm
-
Weight: 95g
-
Uses: garage doors, motorcycles, car alarm products, home
security products, wireless remote control products, industrial control
products.
How to set up the 8-bits code of the transmitter:
-
1. Open the transmitter shell, then you will see the circuit
board. There are two rows pads and one row of chip feet on the back side.
-
2. The upper row of pads is “L” side, and the lower row of pads
is “H” side.
-
3. If solder the middle row of chip feet to the “L” side, it is
code 1. If solder the middle row of chip feet to the “H” side, it is code 2.
Don’t solder to any side, it is code 0.
-
4. The 8-bits code order is from left to right (from A1 to A8).
-
5. Here is an example, the 8-bits code in the picture is
00010121, solder as the following way:
-
6. Code 0: don’t solder any side, like A1、A2、A3、A5.
-
7. Code 1: solder to the “L” side, like A4、A6、A8.
-
8. Code 2: solder to the “H” side, like A7.
Matching Transmitters:
-
The receiver can work with different
transmitters, such as model C-2 /C-2L (100M), CWB-2 (50M, waterproof),
CP-2/CP-2L (500M), or CB-2 / CB-2L (1000M) etc.
-
Super long range, with a transmitter (such as
CB-2) to form a complete set, the maximum working distance can reach 2000M in an
open ground.
The maximum working distance is a theoretical data, it shall be operated in an
open ground, no barriers, no any interference. But in the practice, it will be
hindered by trees, walls or other constructions, and will be interfered by other
wireless signals. Therefore, the actual distance may not reach this maximum
working distance.
Magnetic Sucker Antenna:
-
Frequency Range: 300~450MHz
-
Impedance: 50Ω
-
Antenna Length: 15cm
-
Cable Length:1.5m, we also can offer longer
cable, such as 5meters, 10meters, 30meters.
-
Anti-interference, waterproof, shielded wire
set inside.
-
Magnetic stand design for easy to install.
Usage:
-
The receiver can be used to control both DC
0~28V and AC 110~240V equipments.
-
Notice: The receiver is relay output, not
DC/AC power output. Initial state of relay output terminals: Terminals B and C
are Normally Open; Terminals A and B are Normally Closed.
Wiring:
-
If you want to control a DC 12V lamp, do as
following:
1) Connect the positive pole of DC power supply to terminal “+”, and connect the
negative pole of DC power supply to terminal “-”.
2) Connect terminal C to the positive pole of DC power supply, connect terminal
B to the positive pole of DC lamp, and connect the negative pole of DC lamp to
the negative pole of DC power supply.
-
If you want to control an AC 220V lamp, do
as following:
1) Connect the positive pole of DC power supply to terminal “+”, and connect the
negative pole of DC power supply to terminal “-”.
2) Connect terminal C to the live wire of AC power supply, connect terminal B to
one side of AC lamp, and connect another side of AC lamp to the neutral wire of
AC power supply.
Operating (with the transmitter C-2):
-
Press button 1: Turn on relay 1 (connect B and
C, disconnect A and B), the lamp 1 is on.
-
Press button 1 again: Turn off relay 1
(disconnect B and C, connect A and B), the lamp 1 is off.
-
Press button 2: Turn on relay 2 (connect B and
C, disconnect A and B), the lamp 2 is on.
-
Press button 2 again: Turn off relay 2
(disconnect B and C, connect A and B), the lamp 2 is off.
How to pair the transmitter to the receiver:
-
1) Press the learning button of receiver for
1- 2 seconds; signal LED on the receiver is on. The receiver enters into status
of LEARNING.
-
2) Press any one button on transmitter. If
signal LED flashes quickly 15 times and turns off, it means learning is
successful.
-
3) When receiver is in the status of LEARNING,
press again the learning button, signal LED turns off, learning process will be
discontinued.
-
4) The receiver can learn several remote
controls with different codes.
Delete all transmitters:
-
We have learned remote control to the
receiver. If you don’t want the receiver to work with the remote control, you
can delete all codes of remote controls, which are stored in the receiver.
-
Operation: Press and hold the learning button
of receiver until signal LED flashes slowly; release the button, LED keeps slow
flash. That means all stored codes have been deleted successfully.
|
|
|
Shipping:
-
Shipping methods: Ship to Worldwide by Airmail.
-
Delivery time: 10~25 working days (not including week-end and holiday).
-
We will ship the item to your shipping address of PayPal within 1~2 working days after clearance of payment.
-
Please contact us immediately if you want to change your shipping address. We are not responsible for wrong address.
-
We will inform you via Email when shipping your items.
|
|
|
|
Guarantee:
- Guaranty: One year, if the products have any quality problem, we will resend the same unit to you by free, but you need to defray the postage.
|
|
|