|
4 Axis 1.2N.m Stepper Motor 3.5A Driver TB6560 Nema23 USB Interface Board CNC Kit
|
|
1.CNC USB Interface Breakout Board
Features:
1: The maximum matching 5-axis stepper motor driver
2: The two-stage signal processing, signal transmission smooth, powerful anti-jamming
3:5 input interface to define the emergency stop, limit, points in the knife, etc.
4: relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc
5: five-axis job LED display, visual display products, working condition
Electrical performance:
Input Power:5V DC power supply or computer USB to take power
Work axis stepper:Received the highest 5-axis independent driving
Drive:Pulse + direction + enable signal
Weight:About 200G
2.Stepper Motor Driver
HY-DIV168N-3.5A subdivision-type two-phase hybrid stepping motor drive using DC 12 ~ 36V power supply, suitable for drive
Two-phase hybrid stepping motor dynamic voltage 12 to 36V, the current is less than 3.5A outer diameter of 35 to 86 mm.
This drive using the drive's current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth, almost no vibration and noise.
High-speed torque is much higher than other two-phase drive, high positioning accuracy. Widely used in the engraving machine, CNC machine tools, packaging machinery and other high resolution requirements on the device.
Features:
- average current control, two-phase sinusoidal current drive output
- DC 12 ~ 36V power supply, the internal integration of 12V and 5V regulator
- optically isolated signal input / output
- overvoltage, undervoltage, overcurrent, and white short-circuit protection
- 4 file segmentation and automatic half-streaming capabilities up to 16 segments
- file output phase current settings
- high starting speed
- high-speed torque
Electrical parameters:
- Input voltage DC 12 ~ 36V input
- The input current of 1 to 4 amps, select the drive a stepper motor.
- Output current of 0.5A ~ 3.5A
- Temperature Operating Temperature -10 to 45 ℃; Storage temperature -40 ℃ to 70 ℃
- Humidity not condensing, not drops
- Gas prohibit combustible gas and conductive dust
- Weight: 200g
- 1. the definition of control signals:
PUL +: step pulse signal is input side or the positive pulse signal input positive terminal
PUL-: the negative input of the negative input pulse signal or a positive pulse signal
DIR +: stepping direction signal input to the positive terminal or negative pulse signal input to the positive terminal
DIR -: stepping direction signal input of the negative side or reverse step pulse signal input negative terminal
EN +: offline can reset signal input side is
EN-: offline can reset signal input negative terminal
Offline enable signal is active, reset drive failure to prohibit any pulse, the output of the drive
Power component is turned off, the motor holding torque.
- 2.Control signal connections:
PC control signal can be high, also can be low effective. When active high, the control signal
The negative side together as a signal to active low, positive side of all control signals together as a signal common.
3.250W 24V 10A switching power supply
4.57BYGH56-401A Stepper Motor(1.2N.m 2.8A）
-
Step Angle Accuracy: +-5%(full step, no load)
-
Resistance Accuracy: +-10%- Inductance Accuracy: +-20%
-
Temperature Rise: 80 Degrees Celsius CMax.(ratod current,2 phase on)- Ambient Temperature: -10°C-+50°C
-
Insulation Class: B
-
Dielectric Strength: 500V AC for one minute
-
Shaft Radial Play: 0.06Max.(450g-load)
-
Shaft Axial Play: 0.08Max.(450 9-load)
Wiring
Black: A+
Green: A-
Red: B+
Blue: B-
|
Model
|
Step angle
|
Motor length
|
Rated current
|
Phase resistance
|
Phase inductance
|
Holding torque
|
Lead wire
|
Rotor inertia
|
Weight
|
|
Single Shaft
|
°
|
L(mm)
|
A
|
Ω
|
mH
|
Oz-in
|
Kgf.cm
|
No.
|
g.cm2
|
kg
|
|
57BYGH56-401A
|
1.8
|
56
|
2.8
|
0.9
|
2.5
|
175
|
12.6
|
4
|
300
|
0.7
|
|
|
|
|
Very Important Note: If there were any problem during your using of this machine,please contact us first, don't try to open or take apart the machine by yourself
Note: Your valid phone number is very necessary for the shipping,please provide it when you order
The product can be shipped by DHL or other Express, but a surcharge of US$50 will be applied on the shipment when your location is remote. Remote is defined as islands and highlands; or a post code/zip code that is difficult to serve; or a suburb/town that is distant, inaccessible or infrequently served
Any customs duty applied to the parcel should be covered by the buyer
As has been stated on the eBay item description, Import duties, taxes and charges are not included in the item price and shipping charges
These charges be at the buyer responsibility. meanwhile the customs tax depend on the buyer local customs office
|
|
|
 |
- 1 x USB CNC breakout board
- 4 x TB6560 3.5A stepper motor driver
- 4 x Stepper Motor 57BYGH56-401A
- 1 x 250W 24V 10A power supply
|
|
| |
|
|
|
Shipping
- Item will be shipped within 2-3 business days of cleared payment via Post Airmail.
- We only ship to buyer's PayPal address, please confirm your address on PayPal before you bid.
- Registered air mail takes 10-20 business days to most Countries: US, Canada, UK, Australia and Europe.
- Optionally, Express Shipments with tracking service via EMS/DHL/UPS takes 5 to 10 business days.
- We would post the tracking number on the order page as soon as it's available.
|
|
|
|
|
Important Note:
- If you have any concern about the purchase,PLEASE feel free to contact us first, we're always ready to help.
- Please kidly note that this is international shipping, delay happens occasionally due to unexpected cases.
- Any customs tax applied to the parcel should be convered by the buyer.
- Please remember to write your phone number which is necessary for the shipping.
|
|
|
|
Payment
- We only accept PayPal.
- Payment must be made within 7 calendar days of the auction end time. Non-Paying bidders will be reported.
|
|
|
|
Refund
- It is buyer's responsibility to contact us within 30 calendar days of receiving a defective product. Otherwise, no replacement or refund will be made. All items MUST be returned in their original condition.
- Buyer is responsible for shipping and proof of delivery on all returns.
|
|
|
|
