LORA32 868MHZ OLED 1Pair/LORA32 915MHZ OLED 1Pair

Description:
The 868/915MHz antenna needs to be in connection with the IPEX interface (if the antenna is not connected, it may damage the LoRa chip)
Lithium battery charge and discharge circuit, when the battery is full, the blue LED will stop working. When using, pay attention to the positive and negative of the battery, otherwise it will be damaged!
With IO port touch screen touch signal input, you need to add the 100nF pull-down capacitor to this pin!
Note:This product does not include the battery.
Example:
This product is a SX1276 chip based on ESP32 WIFI increased OLED, namely LoRa remote modem, 868-915MHz frequency, high sensitivity is over-148dBm, + 20dBm output power, high reliability, long transmission distance.
the onboard 32MB Flash wi-fi antenna, 0.96 inch blue oled display, lithium battery charging circuit, CP2102 interface and USB serial chip, the perfect support for Arduino development environment, can be used for program checking and product development is very easy and fast.
Operating voltage: 3.3V to 7V
Operating temperature range: -40 째 C to + 90 째 C
Support for Sniffer software protocol analysis, Station, SoftAP, and Wi-Fi Direct modes
Data rates: 150 Mbps @ 11n HT40., 72 Mbps @ 11n HT20, 54 Mbps @ 11g, 11 Mbps @ 11b
transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n
receiver sensitivity up to -98 dBm
UDP sustained throughput of 135 Mbps

Pin diagram:

Use legend:

Note:This product does not include the battery.
Package included:(LORA32 868MHZ OLED 1Pair)
1 x 868MHZ Transmit ESP32 OLED Module
1X 868MHZ receive ESP32 OLED Module
2 x Line
4 x Pin
2 x Spring Antenna
Package included:(LORA32 915MHZ OLED 1Pair )
1 x 915MHZ Transmit ESP32 OLED Module
1X 915MHZ receive ESP32 OLED Module
2 x Line
4 x Pin
2 x Spring Antenna

LORA32 868MHZ OLED SD 1Pair/LORA32 915MHZ OLED SD 1Pair

Product Description：
Working voltage: 1.8~3.7v
Acceptable current：10~14mA
Transmit current:120mA@+20dBm
90mA@+17dBm
29mA@+13dBm
Operating frequency: 868M/915M
Transmit power: +20dBm
Receive sensitivity :-139dBm@LoRa &62.5Khz&SF=12&146bps
-136dBm@LoRa &125Khz&SF=12&293bps
-118dBm@LoRa &125Khz&SF=6&9380bps
-123dBm@FSK&5Khz&1.2Kbps
Frequency error：+/-15KHz
FIFO space：64Byte
Data rate：1.2K~300Kbps@FSK
0.018K~37.5Kbps@LoRa 
Modulation Mode ：FSK,GFSK,MSK,GMSK,LoRa TM，OOK
Interface form ： SPI
Sleep current ：0.2uA@SLEEP
1.5uA@IDLE
Operating temperature ：-40℃——85℃
Digital RSSI function
Automatic frequency correction
Automatic gain control 
RF wake-up function
Low voltage detection and temperature sensor
Fast wake-up and frequency hopping
Highly configurable data packet handler
Compared with LORA32 v1.0

Pin Diagram

Product Using

Product Details:

Notice:The shipping list does not include battery and SD card.

Package included:(LORA32 868MHZ OLED SD 1Pair）
1 X TTGO lora32 V2.0 868Mhz Transmit Module
1 X TTGO lora32 V2.0 868Mhz receive Module
2 X Antenna
2 X Power cable
Package included:(LORA32 915MHZ OLED SD 1Pair)
1 X TTGO lora32 V2.0 915Mhz Transmit Module
1 X TTGO lora32 V2.0 915Mhz receive Module
2 X Antenna
2 X Power cable

LORA SX1276 ESP32 OLED

868MHz-915MHz SX1276 ESP32 LoRa 0.96 Inch Blue OLED Display Bluetooth WIFI Lora Kit 32 Module IOT Development Board for Arduino

If you need the document of this product,please contact us freely.

LoRa send and receive test

WIFI Kit series is the new development of the cost-effective networking program, the main chip using ESP32, LX6 dual-core processor, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b / g / N HT40 Wi-Fi transceiver, baseband, protocol stack and LWIP, integrated dual-mode Bluetooth (traditional Bluetooth and BLE low power Bluetooth).

This product is based on the WIFI Kit 32 added SX1276 chip, that is, LoRa ™ remote modem, Applicable frequency:868MHz -915MHz frequency, about -148dBm high sensitivity, +20 dBm power output, high reliability, transmission distance (measured open area communication distance 2.6Km).


Onboard 32MByte Flash, Wi-Fi antenna, 0.96-inch blue OLED display, lithium battery charging circuit and interface, CP2102 USB to serial chip, the perfect support for Arduino development environment, can be very simple and fast for program verification and product development.

Technical Parameters:
Flash: 32M-Bits
Processor: for Tensilica LX6 Dual Core
Master chip: ESP32
LoRa chip: SX1276
Support frequency band: 868-915MHZ
Open communication distance: 2.8KM
Computing capacity: up to 600DMIPS
Dual-mode Bluetooth: traditional Bluetooth and BLE low-power Bluetooth
Development environment: perfect support for Arduino
Operating voltage: 3.3-7V
Operating temperature range: -40-90 ℃
Receiver sensitivity: -139dBm (SF12, 125KHZ)
UDP continuous throughput: 135Mbps
USB adapter chip: CP2102
Support mode: Sniffer, Station, softAP and Wi-Fi Direct
Transmit power: 19.5dBm@11b, 16.5dBm@11g, 15.5dBm@11n
Data rate: 150Mbps @ 11n HT40, 72Mbps @ 11n HT20,
54Mbps @ 11g, 11Mbps @ 11b

Package Includes:
1 X ESP32 Lora OLED development board
2 X Pin header
2 X Pin header stickers

LORA SX1278 433Mhz

The 433MHz antenna must be used in conjunction with the IPEX interface (if the 

antenna is not connected, it may damage the LoRa chip)Lithium battery charging 

and discharging circuit, when the battery is full, the blue LED will stop working. 

When using, pay attention to the positive and negative of the battery, otherwise 

it will be damaged！

Using the IO port touch screen touch signal input, you need to add the 100nF 

pull-down capacitor at this pin!

Example:

This product is a SX1278 chip based on ESP32(revision 1) WIFI increased OLED, namely LoRa 

remote modem, 433MHz frequency, high sensitivity is about -148dBm, +20dBm output 

power, high reliability, long transmission distance.

The onboard 16 Mt bytes (128 Mt ), Wi-Fi antenna, 0.96 inch blue OLED display, lithium battery 

charging circuit, CP2102 interface and USB serial chip, the perfect support for Arduino 

development environment, can be used for program verification and product development 

is very simple and fast.

Operating voltage: 3.3V to 7V

Operating temperature range: -40 degrees C to +90 degrees C

Support for Sniffer, Station, softAP, and Wi-Fi Direct modes

Data rates: 150 Mbps@11n HT40, 72 Mbps@11n HT20, 54 Mbps@11g, 11 Mbps@11b

Transmit power: 19.5 dBm@11b, 16.5 dBm@11g, 15.5 dBm@11n

Receiver sensitivity up to -98 dBm

UDP sustained throughput of 135 Mbps

Pin reference description

Test details

For example One

（1）LoRaSender

#include <SPI.h>

#include <LoRa.h>

#include<Arduino.h>

// GPIO5  -- SX1278's SCK

// GPIO19 -- SX1278's MISO

// GPIO27 -- SX1278's MOSI

// GPIO18 -- SX1278's CS

// GPIO14 -- SX1278's RESET

// GPIO26 -- SX1278's IRQ(Interrupt Request) 

#define SS      18

#define RST     14

#define DI0     26

#define BAND    433E6  

int counter = 0;

void setup() {

pinMode(25,OUTPUT); //Send success, LED will bright 1 second

Serial.begin(115200);

while (!Serial); //If just the the basic function, must connect to a computer

SPI.begin(5,19,27,18);

LoRa.setPins(SS,RST,DI0);

//  Serial.println("LoRa Sender");

if (!LoRa.begin(BAND)) {

Serial.println("Starting LoRa failed!");

while (1);

}

Serial.println("LoRa Initial OK!");

}

void loop() {

Serial.print("Sending packet: ");

Serial.println(counter);

 // send packet

 LoRa.beginPacket();

LoRa.print("hello ");

LoRa.print(counter);

LoRa.endPacket();

counter++;

digitalWrite(25, HIGH);   // turn the LED on (HIGH is the voltage level)

delay(1000);                       // wait for a second

digitalWrite(25, LOW);    // turn the LED off by making the voltage LOW

delay(1000);                       // wait for a second

delay(3000);

}

For example Two

(2)LoRaReceiver

#include <SPI.h>

#include <LoRa.h>

// GPIO5  -- SX1278's SCK

// GPIO19 -- SX1278's MISO

// GPIO27 -- SX1278's MOSI

// GPIO18 -- SX1278's CS

// GPIO14 -- SX1278's RESET

// GPIO26 -- SX1278's IRQ(Interrupt Request)

#define SS      18

#define RST     14

#define DI0     26

#define BAND    433E6

void setup() {

Serial.begin(115200);

while (!Serial); //if just the the basic function, must connect to a computer

delay(1000);

Serial.println("LoRa Receiver");

SPI.begin(5,19,27,18);

LoRa.setPins(SS,RST,DI0);

if (!LoRa.begin(BAND)) {

Serial.println("Starting LoRa failed!");

while (1);

  }

}

void loop() {

// try to parse packet

int packetSize = LoRa.parsePacket();

if (packetSize) {

// received a packet

Serial.print("Received packet '");

 // read packet

 while (LoRa.available()) {

Serial.print((char)LoRa.read());

    }

 // print RSSI of packet

Serial.print("' with RSSI ");

Serial.println(LoRa.packetRssi());

}

}

For example three

(3)LoRaReceiverCallback

#include <SPI.h>

#include <LoRa.h> 

// GPIO5  -- SX1278's SCK

// GPIO19 -- SX1278's MISO

// GPIO27 -- SX1278's MOSI

// GPIO18 -- SX1278's CS

// GPIO14 -- SX1278's RESET

// GPIO26 -- SX1278's IRQ(Interrupt Request)

#define SS      18

#define RST     14

#define DI0     26

#define BAND    433E6

void setup() {

Serial.begin(115200);

while (!Serial); //if just the the basic function, must connect to a computer

SPI.begin(5,19,27,18);

LoRa.setPins(SS,RST,DI0);

Serial.println("LoRa Receiver Callback");

if (!LoRa.begin(BAND)) {

Serial.println("Starting LoRa failed!");

while (1);

}

// register the receive callback

LoRa.onReceive(onReceive);

// put the radio into receive mode

LoRa.receive();

}

void loop() {

// do nothing

}

void onReceive(int packetSize) {

// received a packet

Serial.print("Received packet '");

// read packet

for (int i = 0; i < packetSize; i++) {

Serial.print((char)LoRa.read());

}

// print RSSI of packet

Serial.print("' with RSSI ");

Serial.println(LoRa.packetRssi());

}

For example four

#include <Wire.h>  // Only needed for Arduino 1.6.5 and earlier

#include "SSD1306.h" // alias for `#include "SSD1306Wire.h"`

#include "images.h"

//OLED pins to ESP32 0.96OLEDGPIOs via this connecthin:

//OLED_SDA -- GPIO4

//OLED_SCL -- GPIO15

//OLED_RST -- GPIO16

SSD1306  display(0x3c, 4, 15);

#define DEMO_DURATION 3000

typedef void (*Demo)(void);

int demoMode = 0;

int counter = 1;

void setup() {

pinMode(16,OUTPUT);

digitalWrite(16, LOW);    // set GPIO16 low to reset OLED

delay(50);

digitalWrite(16, HIGH); // while OLED is running, must set GPIO16 in high

Serial.begin(115200);

Serial.println();

Serial.println();

// Initialising the UI will init the display too.

display.init();

display.flipScreenVertically();

display.setFont(ArialMT_Plain_10);

}

void drawFontFaceDemo() {

// Font Demo1

// create more fonts at http://oleddisplay.squix.ch/

display.setTextAlignment(TEXT_ALIGN_LEFT);

display.setFont(ArialMT_Plain_10);

display.drawString(0, 0, "Hello world");

display.setFont(ArialMT_Plain_16);

display.drawString(0, 10, "Hello world");

display.setFont(ArialMT_Plain_24);

display.drawString(0, 26, "Hello world");

}

void drawTextFlowDemo() {

display.setFont(ArialMT_Plain_10);

display.setTextAlignment(TEXT_ALIGN_LEFT);

display.drawStringMaxWidth(0, 0, 128,

"Lorem ipsum\n dolor sit amet, consetetur sadipscing elitr, sed diam nonumy eirmod tempor invidunt ut labore." );

}

void drawTextAlignmentDemo() {

// Text alignment demo

display.setFont(ArialMT_Plain_10);

// The coordinates define the left starting point of the text

display.setTextAlignment(TEXT_ALIGN_LEFT);

display.drawString(0, 10, "Left aligned (0,10)");

// The coordinates define the center of the text

display.setTextAlignment(TEXT_ALIGN_CENTER);

display.drawString(64, 22, "Center aligned (64,22)");

// The coordinates define the right end of the text

display.setTextAlignment(TEXT_ALIGN_RIGHT);

display.drawString(128, 33, "Right aligned (128,33)");

}

void drawRectDemo() {

// Draw a pixel at given position

for (int i = 0; i < 10; i++) {

display.setPixel(i, i);

display.setPixel(10 - i, i);

}

display.drawRect(12, 12, 20, 20);

// Fill the rectangle

display.fillRect(14, 14, 17, 17);

 // Draw a line horizontally

display.drawHorizontalLine(0, 40, 20);

// Draw a line horizontally

display.drawVerticalLine(40, 0, 20);

}

void drawCircleDemo() {

for (int i=1; i < 8; i++) {

display.setColor(WHITE);

display.drawCircle(32, 32, i*3);

if (i % 2 == 0) {

display.setColor(BLACK);

}

display.fillCircle(96, 32, 32 - i* 3);

}

}

void drawProgressBarDemo() {

int progress = (counter / 5) % 100;

// draw the progress bar

display.drawProgressBar(0, 32, 120, 10, progress);

// draw the percentage as String

display.setTextAlignment(TEXT_ALIGN_CENTER);

display.drawString(64, 15, String(progress) + "%");

}

void drawImageDemo() {

// on how to create xbm files

display.drawXbm(34, 14, WiFi_Logo_width, WiFi_Logo_height, WiFi_Logo_bits);

}

Demo demos[] = {drawFontFaceDemo, drawTextFlowDemo, drawTextAlignmentDemo, drawRectDemo, drawCircleDemo, drawProgressBarDemo, drawImageDemo};

int demoLength = (sizeof(demos) / sizeof(Demo));

long timeSinceLastModeSwitch = 0;

void loop() {

// clear the display

display.clear();

// draw the current demo method

demos[demoMode]();

display.setTextAlignment(TEXT_ALIGN_RIGHT);

display.drawString(10, 128, String(millis()));

// write the buffer to the display

display.display();

if (millis() - timeSinceLastModeSwitch > DEMO_DURATION) {

demoMode = (demoMode + 1)  % demoLength;

timeSinceLastModeSwitch = millis();

}

counter++;

delay(10);

}

Note:This product does not include the battery.

shipping list：

ESP32(revision 1) OLED *1

Line *1

pin*2

433m Spring Antenna*1

LORA ESP32-S3FN8 SX1262 433Mhz