Long Magnetic Substrate Guide for ULTILE Precision Wafer Cutters

Product Descriptions Long magnetic clamps are used to securely hold wafers and substrates in place for cutting/scribing. This eliminates the need to use hand to hold the substrate. It is magnetically attached to the base plate of the cutting table, and the position of the magnetic clamp can be adjusted. SKU# GC0116 Length: 110 mm (can hold up to 8 inch size wafers) A pair (qty. 2) should be ordered for use on the precision cutter. The list price is for qty. 1. Cutting Wheels Options for ULTILE Precision Glass and Wafer Cutters Four different Carbide cutting wheels are available to handle standard materials from 0.15 mm up to 3 mm in thickness. There are also four different Diamond cutting wheels available for use on harder materials (such as sapphire, YSZ, etc.) ranging from 0.15 mm to 3.0 mm in thickness. These cutting wheels are ordered together with new cutters or as replacement cutting wheels. The ULTILE Precision Glass and Wafer Cutters are the highest precision lab scale glass and wafer cutters that provide the best possible edge quality after cutting. These glass and wafer cutting tools have an ergonomic design for the ease-of-use for the users to quickly and easily cut larger size glass, crystal substrates and semiconductor wafers into smaller pieces. The cutters can be equipped with either a carbide or diamond cutting wheel. Technically they are not cutters, but rather they scribe the material and allow the user to make a clean break along the scribe line. The ULTILE Precision Glass and Wafer Cutters feature an ergonomic design with an adjustable pressure dial, which allows for consistent scribing with every pass, with no pressure needed from the user during scribing. Typical materials that can be cut with the ULTILE Precision Glass and Wafer Cutters include:Transparent Conductive Oxide Coated Glass (such as ITO glass, FTO glass and AZO glass)Quartz (such as fused quartz, quartz wafers, plates, slides, and coverslips)Silicon wafersSapphire wafers and substratesOther crystal substrates and wafers (A to Z) Materials can normally be cut into pieces as small as 3cm x 3cm, but the minimum size is determined by the thickness of the material. Thinner materials, such as coverslips and silicon wafers can be cut to less than 5mm x 5mm in size with a little practice. This allows users to create their own custom size substrates to meet their specific device design requirements. Operation is simple and repeatable:1) Adjust the height of the wheel based on the thickness of the material being cut.2) Set the proper pressure between 1 and 50 N 3) Align substrate material along the integrated scale to achieve the desired size4) Use the optional magnetic holder to secure the material in place5) Pull back on the scribing handle to create the scribing mark6) Achieve a perfect cleave along the scribing mark either by hand or by using a pair of glass breaking pliers. The ULTILE Precision Glass and Wafer Cutters are available in five sizes to accommodate a wide range of sample sizes: 100 mm (4 inch), 200 mm (8 inch), 300 mm (12 inch), 400 mm (16 inch), and 500 mm (20 inch).

Long Magnetic Substrate Guide for ULTILE Precision Wafer Cutters

Product Descriptions

Long magnetic clamps are uséd to securely hold wafers and substrates in place for cutting/scribing. This eliminates the need to use hand to hold the substrate. It is magnetically attached to the base plate of the cutting table, and the position of the magnetic clamp can be adjusted.

SKU# GC0116

Length: 110 mm (can hold up to 8 inch size wafers)

A pair (qty. 2) should be ordered for use on the precision cutter. The list price is for qty. 1. 

Cutting Wheels Options for ULTILE Precision Glass and Wafer Cutters

Four different Carbide cutting wheels are available to handle standard materials from 0.15 mm up to 3 mm in thickness. There are also four different Diamond cutting wheels available for use on harder materials (such as sapphire, YSZ, etc.) ranging from 0.15 mm to 3.0 mm in thickness.

These cutting wheels are ordered together with new cutters or as replacement cutting wheels.

The ULTILE Precision Glass and Wafer Cutters are the highest precision lab scale glass and wafer cutters that provide the best possible edge quality after cutting. These glass and wafer cutting tools have an ergonomic design for the ease-of-use for the users to quickly and easily cut larger size glass, crystal substrates and semiconductor wafers into smaller pieces. The cutters can be equipped with either a carbide or diamond cutting wheel. Technically they are not cutters, but rather they scribe the material and allow the user to make a clean break along the scribe line. The ULTILE Precision Glass and Wafer Cutters feature an ergonomic design with an adjustable pressure dial, which allows for consistent scribing with every pass, with no pressure needed from the user during scribing.

Typical materials that can be cut with the ULTILE Precision Glass and Wafer Cutters include:
Transparent Conductive Oxide Coated Glass (such as ITO glass, FTO glass and AZO glass)
Quartz (such as fuséd quartz, quartz wafers, plates, slides, and coverslips)
Silicon wafers
Sapphire wafers and substrates
Other crystal substrates and wafers (A to Z)

Materials can normally be cut into pieces as small as 3cm x 3cm, but the minimum size is determined by the thickness of the material. Thinner materials, such as coverslips and silicon wafers can be cut to less than 5mm x 5mm in size with a little practice. This allows users to create their own custom size substrates to meet their specific device design requirements.

Operation is simple and repeatable:
1) Adjust the height of the wheel based on the thickness of the material being cut.
2) Set the proper pressure between 1 and 50 N
3) Align substrate material along the integrated scale to achieve the desired size
4) Use the optional magnetic holder to secure the material in place
5) Pull back on the scribing handle to create the scribing mark
6) Achieve a perfect cleave along the scribing mark either by hand or by using a pair of glass breaking pliers.

The ULTILE Precision Glass and Wafer Cutters are available in five sizes to accommodate a wide range of sample sizes: 100 mm (4 inch), 200 mm (8 inch), 300 mm (12 inch), 400 mm (16 inch), and 500 mm (20 inch).

Shipping info

Click the Shipping & Payments tab above the listing description for more info

Click the Shipping & Payments tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYMENT


Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.

We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).

The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.

Thank you for shopping with us on eBay!

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© MSE Supplies LLC

Click the Shipping & Payments tab above the listing description for more info

Accepted Payment Methods

Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.

We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).

The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.

Thank you for shopping with us on eBay!

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.


Additional Information:
"Broken or damaged items must be reported immediately upon receiving your package (within 5 business days upon delivery). All materials and equipment are considered as received in good condition upon signature of delivery confirmation. Please inspect these items for damage prior to signing off on the condition. If it becomes necessary to return a damaged item to MSE Supplies, please contact us for a Return Merchandise Authorization (RMA) number within 30 days of receipt of the product. MSE Supplies must receive the product within 15 days of MSE Supplies issuing the Return Merchandise Authorization (RMA). The product must be in the original packaging or the return will be rejected. RMA numbers must appear on the packing list and items being returned must be packaged and shipped in accordance with all applicable regulation. All items are subject to a 25% restocking fee. \r\n\r\nItems not returnable for credit include: open or damaged containers; materials past their expiration date or with an expiration date too short for resale; custom or special orders; non-recurring engineering (NRE) cost charged to the order, and chemicals of any type. Any supplies or equipment that have been uséd and are being returned for a warranty repair may require that a decontamination form be filled out. Please contact MSE Supplies for this form."