Product Specifications:

(Please make sure you take the proper measurements before purchasing)

Quantity: 4pcs
Thickness: 1.5 inch (38mm) per spacer

Hub Bore Size: 126.15mm
Vehicle Bolt Pattern: 8x6.5" (8x165.1mm)
Wheel Bolt Pattern: 8x6.5" (8x165.1mm)
Thread Pitch: M14x1.5

Compatibility Information:

(Please check the compatibility chart carefully before purchasing)

Chevrolet
Chevrolet Avalanche 2500 2002-2006
Chevrolet C2500 1988-1998 (8 Lug Vehicles)
Chevrolet C3500 1988-1998
Chevrolet Express 2500 1997-2014 (8 Lug Vehicles)
Chevrolet Express 3500 1997-2014 (8 Lug Vehicles)
Chevrolet K2500 1988-1998 (8 Lug Vehicles)
Chevrolet K3500 1988-1998
Chevrolet Silverado 1500 HD 2001-2003&2005-2006
Chevrolet Silverado 2500 1999-2009
Chevrolet Silverado 2500 HD 2001-2010
Chevrolet Silverado 3500 2001-2007
Chevrolet Silverado 3500 HD 2007-2010
Chevrolet Suburban 2500 2000-2013

GMC
GMC C2500 1988-1998 (8 Lug Vehicles)
GMC C3500 1988-1998
GMC K2500 1988-1998 (8 Lug Vehicles)
GMC K3500 1988-1998
GMC Savana 2500 1997-2014 (8 Lug Vehicles)
GMC Savana 2500 1997-2014 (8 Lug Vehicles)
GMC Sierra 2500 HD 2001-2010
GMC Sierra 3500 2001-2006
GMC Sierra 3500 HD 2007-2010
GMC Yukon XL 2500 2000-2013

Hummer
Hummer H2 2003-2009

Nissan

Nissan NV1500 2012-2014 (Only for M14x1.5)
Nissan NV2500 2012-2014 (Only for M14x1.5)
Nissan NV3500 2012-2014 (Only for M14x1.5)

Ram
Ram 2500 2012-2013 (Only for M14x1.5)
Ram 2500 2014-2022
Ram 3500 2012-2013 (Only for M14x1.5)
Ram 3500 2014-2022

How to choose the correct wheel spacers:

STEP. Check 3 specifications
The following is the easy and simple way to check the bolt pattern/PCD, center/hub bore and thread pitch. If you donot sure, please just message us with the year, make and model of vehicle.

1). Check Vehicle Bolt Pattern/PCD For 4-lug, 6-lug, 8-lug, measure the segment from the CENTER of a bolt hole TO the CENTER of another hole. 5 lug is different, you need to measure the back of the hole to the center of the second bolt hole (not center point).(See Bolt Pattern Diagram below)

2). Check Vehicle Hub/Center Bore Size Measure the diam of the center bore on hub, make sure the spacer's diam is equal to or bigger than the axle diameter.

3). Check Vehicle Thread Pitch There are different types of studs, such as M12x1.25, M14x1.5, M12x1.5, 1/2"x20, 9/16"x18, please make sure the studs of wheel spacers is the same as the vehicle's, otherwise the spacer will not fit.

How to install the wheel spacers:

1). IMPORTANT - ADAPTER OR SPACER MUST SIT FLUSH AGAINST VEHICLE HUB, AND WHEEL MUST SIT FLUSH AGAINST ADAPTER OR SPACER! Stock studs must be trimmed down (shortened) if they protrude past the surface of the adapter or spacer. If not, vibration or other problems can occur. Some wheels have pockets that may allow for no stud trimming. If not, studs MUST be trimmed.

2). Make sure the mounting surface (vehicle hub) is clean and flat, and remove all retaining clips.

3). Install the adapter to the vehicle, with the proper lug nuts, and torque to manufacturer’s wheel torque specs.

4). Install the wheel to the adapter by torquing to the vehicle manufacturer’s wheel torque specifications (again, max 140 ft-lbs). Please assure the proper thread engagement (6 to 8 full turns) on lug nuts or bolts.

5). Drive the vehicle. If no problems (noise, vibration, anything out of the ordinary), drive about 5 miles, then re-torque the lug nuts attaching the spacer or adapter to the hub.