INTENSIVE LASH AND BROW TINT
Application Instructions
FOR PROFESSIONAL USE
ONLY
We recommend that you
carry out a skin allergy test 24 hours before the treatment. To
do the test mix a tiny amount of the dye with one drop of the
developer, and then apply to the crook of the elbow or behind
the ear. 24 hours later, check the area for any signs of
redness, rash or soreness, if you see any of these signs, do not
proceed with the treatment.
1) Preparing the
Client:
| Client
must be sitting upright in a chair with the head slightly tilted
back. DO NOT APPLY IF THE HEAD OR THE BODY IS LAID BACK
IN A RECLINED POSITION. |
 |
2) Preparing the tint:
Shake the developer well
before use. Mix ¾ inch (2 cm) of Colour Cream with 2-4 drops of
the Developer until the consistency becomes a creamy paste.
(Ensure that consistency is not runny or drippy.). Let the mix
develop for 3 minutes while the client is being prepared.
3) Preparing the area
to be treated
|
Cleanse the area to be treated
thoroughly ensuring that it is completely free of
makeup, oil and grease. Use non-oily makeup
remover
(  ), then
finish cleansing by wiping the area with a cotton
pad damped in lukewarm water. Dry and then apply Skin
protection cream
( ) under
the lower lid and around the eyes and / or eyebrows
(if eyebrows also to be tinted) . Place protection
pad
( ) under
the lower lid to prevent the tint from staining the
skin. |
 |
 |
 |
4) Application
for eyelashes:
|
Using
a tinting brush or application stick, apply the mix
to the lower lashes first ensuring that the tint
covers the hair from base to tip. Make sure that
corner lashes are also covered. Then apply the tint
to upper lashes from base to tip. Make sure that
corner lashes are covered. |
 |
 |
for eyebrows:
|
Apply the mix to the eyebrows using a tinting brush or
application stick, ensure that you cover all hairs of
the eyebrows. |
 |
When tinting is completed,
instruct the client to sit quietly and relax until the end of
the treatment.
5) Processing time:
this depends on the following
factors: original hair colour, tint desired, coarseness and
condition of the client’s hair, and room temperature.
Although the usual processing time is 10 minutes for lashes and
3 minutes for brows, these times may produce results darker than
expected. If you are working with Middle Brown, Brown or
Graphite, we recommend that you allow eyelashes to develop for 3
minutes and the eyebrows to develop for one and half minutes.
Then cleanse them and check the colour. If the eyelashes and/or
eyebrows are not dark enough, re-apply and allow to them to
process again until the desired colour is achieved. A general
rule is that the longer you leave it, the darker the colour you
get.
6) Completing and
Finishing the treatment:
|
Use a
cotton swab dampened in soap and water to remove any
tint from the skin. DO NOT USE TINT SPOT CLEANSER ON THE
SKIN. DO NOT ALLOW THE CREAM OR DEVELOPER TO REACH THE
EYES, NOSTRILS, OR EARS. IF THIS HAPPENS, IMMEDIATELY
FLUSH WITH WARM WATER AND DRY THE AREA. |
 |
|
Gently
Remove the eye protection pads. Then, with the
client’s eye closed, use a cotton ball soaked in
warm water to remove product until no residues are
visible. Use tissues to capture any dripping or
excess. |
 |
 |
NOTE: The colour of the
mixture is not the colour that the hair will be once it is
tinted. To get an idea of the final colour, leave a wooden
applicator in the mixture for the desired time.
Instruction videos are available at www.makkicosmetics.com
the developer may look a bit
thick due to changing room temperature, this does not affect the
product quality. Always store in cool place.
.
