Title :  DIY SECURITY WIRELESS GSM AUTODIAL HOME HOUSE OFFICE BURGLAR INTRUDER Anti-theft ;
 
Package inlcuded:
 
4 PCS Wireless Sensor ;
1 PCS 4 channel relay receiver;
 
 
Receiver :
 

 

1.operating voltage: DC 12V ;       

2.static operating current:≤6mA;

3.Working temperature :-20°C- +80°C;        

4.Receive sensitivity:≥-105dBm;

5.the working frequency:433.92MHZ;
6.output current:≤10A;

7.size:74.5*54.5*27mm ;

8: Momentary Mode ,Latch Mode  , Toggle Mode can be adjustable by jumper .
9. Pls connect the receiver modules properly before power supply ;
10: 4 channels;
11: Learning function (can works with EV1527 SC2262 PT2262 PT2264 PT2260 remote , can store 16 pcs different code remote );
12: Max load : 1000W;   
 
Advantage :
1:  Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 Learning remotes to re-learn;
 

Output:

A.singnal Inter-locking (Latch)----connect 1  and 2 ;

B.singnal Self-locking (Toggle) ---- connect 2 and 3 ;

C.singnal Non-locking (Momentary ) ---- disconnect the jumper ;

Inter-locking (Latch): 4-way relay each other to switch, when relay A  is working and locked  ,  relay B C D corresponding to switch off; when B is working and locked , corresponding relay A C D swith off ; Only 1 relay is on among 4 relays A B C D;
 
Non-locking  type (Momentary): Press A and hold it , then A is on.Same as Relay B C D ;
 

Self-lock type (Toggle): 4 channels opens and closes independently, 4 channels can work together ,they don’t affect each other . press A button, A relay of work and locked, press again then  disconnected; Same as B C D .

 

Learning method and steps

1.       Keep pressing learnig key on receiver board , release the button when LED is off , enter the learning state ;

2.       Press any key on remote control within 5 seconds , LED flash 3 times and then turn on , then ithave success in learning .

Clear the deposit information

Keep Pressing Learning Key , LED turns off , Wait 10 Seconds , LED turn on , that deposited information has been successfully cleared ;

433Mhz Wireless Door / Windown Sensor

、

 
1)Feature:

It will work with most standard security system. Pull out the antenna of the magnetic detecto: when the door or window is opened from the closed position, LED 1 will turn to red for 2 seconds, the magnetic detector will be triggered and will send alarming signal to the main unit. Indication of low battery: When the voltage of battery is less than 7.5V, LED 2 will straightly turn on red light. At this time, you nee to immediately change the battery.

 

 

Launch Distance:  50-80 meters (open place) 
Operating Voltage: 12V
Operating Frequency: 433MHz.
Encoding: EV1527 Fixed Code IC ;
Size: 71 x 36 x 15(mm) / 2.8 x 1.4 x 0.6(inch )
Oscillation resistance: 470K ;
Power supply: 12V 23A Battery (the battery is not included ) ;

2)Package: 

1*wireless door sensor

 

 
Similar connection :
 
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V

 

 

Wiring Diagram 2:

DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment

 

Wiring Diagram 3:
All kinds of motor reversing control: DC 1-110V or AC 85-265V DC/AC Motor