This offer is for 4 Universal Joints (Front & Rear).

4 Universal Joints Fitting front and/or rear shaft drives depending on vehicle's specifics.Please check fitment chart for more details.

Fits: 

Please do not make any assumptions as far as fitment is concerned. You must verify that this part will fit your exact model and specifics by doing the following:

1) See the table below if your model is included. If so, then

2) Go to the compatibility chart of the listing above.  If you can’t see the compatibility chart, then click on “see compatible vehicles” at the top of the listing to display the chart.

3) Locate your vehicle in the chart by year, make, model….etc.

4) The left most column, is the notes column with important details. Any restrictions or specifics for which this part will or will not fit will be included in these notes.

In general, the drive of your vehicle (4WD, AWD, ….etc) needs to be known.  Also how many drive shafts does your vehicle have? On which drive shaft you want to install the U-Joint and where on that shaft (front, rear, at transmission….etc.)

BUICK1961-2007
CADILLAC1950-2016
CHEVROLET1967-2016
CHRYSLER2007-2009
DODGE1975-2009
FORD1968-1993
GMC1967-2016
HUMMER2003
ISUZU1996-2008
JEEP2003-2006
LINCOLN1968-1979
MERCURY1979
OLDSMOBILE1954-2004
PLYMOUTH1974-1981
PONTIAC1956-2002
SAAB2005-2009

Premium; Greasable
MOOG premium universal joints are machined to meet or exceed original equipment standards. Each u-joint part is precision-ground to the strictest tolerances, with quality control inspections at every step of the manufacturing process.

Features

  • Bearing cups are cold-formed and case-hardened, then precision-ground to meet or exceed OE standards, for better wear and strength.
  • Superior quality seals are designed to keep contaminants out and to allow for proper lubrication.
  • Needle bearings are precision ground for maximum load-carrying capabilities.
  • Bearing cups utilize a radial design to allow 360° lubricant distribution to all bearing surfaces.
  • High strength steel crosses are forged to meet or exceed OE specifications and are carburized heat-treated for long life.
Bearing Cap Axis 1 Diameter1.125 In.
Bearing Cap Axis 2 Diameter1.125 In.
Bearing Diameter A1.125 In.
Bearing Diameter B1.125 In.
Length A2.557 in.
Length Axis 12.557 in.
Length Axis 22.557 in.
Length B2.557 in.
Bearing Cap Axis 1 Diameter28.5 mm
Bearing Diameter A28.5 mm
Bearing Cap Axis 2 Diameter28.6 MM
Bearing Diameter B28.6 MM
Bearing Cap Type4 Grooved Round Bearings
U-Joint Identification4 Grooved Round Bearings
Length A64.9 mm
Length Axis 164.9 mm
Length Axis 264.9 mm
Length B64.9 mm
Length Measurement BInside of Groove to Inside of Groove plus thickness of 2 Lock Rings
OE SeriesMechanics 3, Saginaw 44 and American Axle 1344
Length Measurement AOutside of Groove to Outside of Groove
Lube Fitting LocationRegular Lube Fitting in Cross
Bearing Type ARound Grooved
Bearing Type BRound Grooved
GreasableYes
LubricateableYes
Alternate/OEM Part Number(s): 10951029, 10952423, 12471502, 12479126, 26042371, 5093377AB, 5093377AC, 68004848, 68004848AB
U-JOINT SPECIFICATIONS
U-Joint Identification4 Grooved Round Bearings
Bearing Type ARound Grooved
Bearing Diameter A - Inch1.125
Bearing Diameter A - mm28.5
Length Measurement AOutside of Groove to Outside of Groove
Length A - Inch2.557
Length A - mm64.9
Bearing Type BRound Grooved
Bearing Diameter B - Inch1.125
Bearing Diameter B - mm28.6
Length Measurement BOutside of Groove to Outside of Groove
Length B - Inch2.557
Length B - mm64.9
OE SeriesMechanics 3, Saginaw 44 and American Axle 1344
LubricateableYES
Lube Fitting LocationRegular Lube Fitting in Cross
Dimension Across Bearing Wing A - Inch1.69
Dimension Across Bearing Wing A - mm42.9
Dimension Across U-Joint A - Inch4.5
Dimension Across U-Joint A - mm114.3
Bearing Type NotesUses Delta Wing Bearings in place of Low Wing Bearings

THANK YOU