☀Emitter: 1x SFT40 LED (6000-6500K)

☀Operating voltage: 2.6V – 4.2V

☀Battery options: 1x 18350

☀Dimension: 89.5mm (length) x40mm (head diameter)

☀Weight: 89grams (without battery)

☀Flashlight body: Aerospace grade 6061 grade aluminum alloy

☀Water resistance i.a.w. IP68

☀Use a rechargeable 18350 battery with a capacity of 850 mA.

☀Automatic Stepdown: Turbo mode steps down to High mode automatically to prevent overheating.

☀Electronic reverse polarity protection from improper battery installation

☀Advanced Temperature Regulation (ATR) technology

(The product uses copyrighted code released under the GNU Public License v3 (GPLv3).

☀To know about the exact source code used in the product,

Notes

✨Due to the TS11 use TIR Optics Lens, this lens needs special cutting and molding, so there will be a little gap(as picture show).Please understand that this is definitely not a quality issue but cannot be avoided.

✨The gap is only visible at certain angles, it's flawless from a top view,and since the gap is on the inside, it doesn't affect water resistance.

So if you don't accept this, please carefully before place order! Thank you!

 

 

 

Operation Instructions

 

Quick Start

Basic usage is simple:

Click to turn the light on or another click to turn it off.

- Hold the button to change brightness.

- Release and hold again to change brightness the other way.

-When on 3 clicks to toggle between stepless dimming and stepped modes

 

Aux button light(work in Advanced UI):

Just like with single-color aux in Anduril, RGB aux has 4 “modes” that are controlled by 7C:

Off-Low-High-Blinking

 

But RGB aux adds color options that are controlled by 7H:

Red-->Yellow (red+green)-->Green-->Cyan (green+blue)-->Blue-->Purple (red+blue)-->White (red+green+blue)-->Disco (random colors)-->Rainbow (changes colors in order)-->Voltage (changes color based on LED voltage)

 

When in the Voltage color option, the colors are:

> 4.4V: white-ish (red+blue+green)

4.1-4.4V: purple (blue+red)

3.9-4.1V: blue

3.7-3.9V: cyan (green+blue)

3.5-3.7V: green

3.3-3.5V: yellow (red+green)

2.9-3.3V: red

< 2.8V: off

 

 

By default, Anduril 2 is set up to use:

While off: low brightness, voltage color mode

While locked out: blinking, disco mode

I think you are in Voltage mode, which is the default. So the color is changing based on the battery voltage. When the flashlight is used, it causes the battery’s voltages to drop a little bit. The voltage goes back up slightly when you turn the flashlight off and the battery rests for a second.

 

-Charge: Max 5V 1A with USB C Rechargeable port.

When charging: power indicator shows red and turns to green after full.

 

That is all the user needs to know for basic use, but there are many more modes and features available for people who want more.

 

Before reading the rest of this manual, it is recommended that users look at the Anduril UI diagram(s), which should be provided along with the flashlight.

Button presses

Button presses are abbreviated using a simple notation:

- 1C: One click.  Press and then quickly release the button.

- 1H: Hold.  Press the button, but keep holding it.

- 2C: Two clicks.  Press and release quickly, twice.

- 2H: Click, hold.  Click two times, but hold the second press.

- 3C: Three clicks.  Press and release quickly, three times.

- 3H: Click, click, hold.  Click three times, but hold the final press.

The same pattern is used with higher numbers too. For example, 10C means ten clicks...  and 10H means ten clicks but hold the final press.