2.2KW 220V ATC Automatic Tool Change Water Cooled Spindle Motor 80mm CNC Milling


Europe countries area:

Austria,Belgium,Bulgaria,CzechRepublic,Denmark,Estonia,Finland,France,Germany,Greece,
Hungary,Ireland,Italy,Latvia,Liechtenstein,Lithuania,Luxembourg,Netherlands,Poland,
Portugal,Romania,Slovakia,Slovenia,Spain,Sweden.  without United Kingdom


Tracking web: (www.dhl.de/en/paket/information/sendungsverfolgung.html) with in one days handling time, When update information on the web,around 3-9 working days arrived


100% Brand New and High Quality


Package include:

  1 x 2.2KW ATC Automatic Tool Changewater cooled spindle motor 24000rpm ISO20 holder   220V 5.4A

User manual will be by email send you


1. Product overview

1) This spindle is built-in type spindle motor, built-in three asynchronous motors,by theinverter control.As the spindle has a compact structure,high power, big torque, small vibration,low noise characteristics,so it can achieve high speed,high powe cutting,high precision and highstability operation.
2) The bearing of spindle use grease lubricated angular to contact bearings,can beachieved lifelong lubricating within the life cycle.
3) The spindle use forced coolling mode to coolling motor,front and rear bearings.Coolantflow through the reasonable arrangement cycle watercourse of the spindle body,thus can takethe heat generated of the spindle rotation speed, to achieve thermal equilibrium,let spindletemperature within a certain constant value. External cooling device effect:maintaining aconstant temperature of the coolant.
4) The spindle built-in PTC 140 temperature sensor(Technical parameters are visible inother sections of this specification),you can read it anytime if you need to protect the motortemperature.
5) The tool clamping methods:this spindle built-in automatic tool change device,shank form
is ISO20


2. Drawing Size Description



Spindle model

RTM80-20-24Z/2.2 220V

Voltage

220V

Maximum speed

24000rpm

Rated frequency

400Hz

Electric current

5.4A

Motor level

Level 2

Rated power

2.2KW (S1)

Peak power

2.2KW (S6)

Rated torque

0.59Nm

Peak torque

0.84Nm

Technical parameters

Spindle blowing dust/seal gas pressure (MPa)

0.2-0.25

Spindle gas seal gas flow

(L/min)

65±10 (When on Working)

Cooling water pressure (MPa)

>=0.25

Cooling water flow (L/min)

>=2.5

Cooling water temperature deg

24-28

Spindle static state pulse (µm)

<=3

Spindle vibration (mm/s)

<=0.8

Spindle diameter (mm)

dia 80 (0/-0.02)

Motor windings Pressure test (V/M)

1000V/1 minute withstanding Voltage test

Tool Interface

ISO20

Inverter Specifications

2.2KW (220V)

Fitment

For castings, aluminum, glass, etc., and other processing




Spindle installation explanation

1)     Circulating Cooling System Description

The system must ensure that the cooling water temperature of supply spindle is between 24-28deg. Usually setting the flow switch in return pipe of the cooling system,to ensure the supply of spindle cooling water. Cooling water requirements: we recommend using distilled water, while recommend Feinuokesi (Fenix) protective agent F1 (using the scale of 1: 200),coolant temperature is 26deg±2deg,inlet, outlet pipe temperature can’t exceed 5 deg.It is allowed As long as other monitoring can ensure fuller spindle cooling.

2) Air sealing control

In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration.

3) Compressed gas quality requirements

The quality requirement of gas which is used in gas seals:

Oil content:<0.01mg/m3

Solid particle:<5µ m

Pressure dew point: <7.5deg(0.7MPa)

4) Running-in program instructions

Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle.

Note: New or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase  to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department.




Shipping


1.) Your order we will ship it within 1-2 business days on payment received.

2.) pls double check your address when you order after, We are not responsible for wrong or undeliverable address

3.) If the order is during the weekends,it will be take extra 2 days longer


Payment

1.) We accept paypal payment,all Paypal must be confirmed (shipping and billing address must match and correct and it need tell us your telephone no for delivery)

2.) pls completed paid within 1-3 working days



Feedback



1.) we care about our valued customers,and will always try to help you,hope to establish long business with you.


2.) Pls give us the opportunity to resolve any problem, we understand the concerns and frustrations you might have,and will try our best to resolve the issues.



3.) Pls contact us by ebay message or email before leaving any negative feedback or opening any cases on the site,we will help you to resolve the problem,



Refund

1.) Defective or wrong item will be offered replacement or refunds after offer the pictures to prove it.

2.) When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos.we will help you to solve all problems.


Contact us

1.) Welcome worldwide customer inquire and questions,we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again

2.) Customer’s satisfaction is very important to us.











































































1.8KW 220V ATC Automatic Tool Change Water Cooled Spindle Motor 80mm CNC Milling
1.8KW Automatic Tool Change 220V ATC Water-cooled spindle motor ISO20 Engraving
EU 1.8KW 220V Water Cooled Spindle CNC fraisage ATC Moteur Automatic Tool Change