The device is in very good cosmetic and technical condition. Fully serviced and working. All functions work as expected.
The heads are in good condition as seen in the photos. full inspection done. All belts and rollers replaced,all mechanisms are greased and cleaned, heads have corrected by TEAC TEST tape,tape patch tested! Motors are cleaned and tested on full working condition.
RECORDING AND PLAY On BOTH DIRECTIONS!! SEE VIDEO FOR DETAILS
PERFECT RECORD SOUND OUTPUT...
Rare Black Edition With Wood Case!!
Direct import from Japan recording studio: (better build than EU version,quality on components are more high and longer life)
Japanese version of 100 volts. replaced to 230V transformer included in sale ,to use in UK or EU!!!
Specifications:
| Type | Tape deck |
| Track format | 4-track, 2-channel |
| Head configuration | 6-head |
| Reel | Types 26 and 17 |
| Tape speed | 19cm/s, 9.5cm/s |
| Motor configuration | 3 Motor |
| Drive system | Closed-loop dual capstan |
| Wow flutter (WRMS) | 19cm/s:0.03%
9.5cm/s:0.04% |
| Frequency Response (EE Tape) | 19cm/s : 30 Hz to 34 kHz
9.5cm/s : 30 Hz to 24 kHz |
| Overall SN ratio (3% THD level, WTD) | dbx out:65dB
dbx in:100dB |
| Dynamic range (dbx in, 1 kHz, peak level) | 115dB |
| Total strain rate (reference level) | 0.8% |
| Stereo Channel Separation (1 khz) | 50dB |
| Input Sensitivity / Impedance | Microphone : 0.25mV-72dB / Compatible Microphone : 200 Ω or more
Line : 60mV/50k Ω |
| Output Level / Impedance | Line : 0.45V/10k Ω or more
Headphone : 8 Ω |
| Pwer | 100 VAC, 50Hz/60Hz |
| Power consumption | 88W |
| External dimensions |
X-1000RBL : 474 mm wide x 490 mm high x 262 mm deep |
Have few more these reel to reel decks in stock as soon sold this one will upload another stay tuned ,also have all spare parts for these machines X10/X7/X1000/X2000/Tascam 32
here is full info about this device translated from Japanesse :
A tape deck equipped with excellent mechanisms such as dbx, closed loop dual capstan, and EE tape support.
Dbx is installed as a noise reduction system.
When recording sound that exceeds the dynamic range of the tape, the dbx system compresses the sound level in the form of the original sound to 1 / 2 in decibels. When playing back the sound, the level of the sound is doubled and returned to the original level. This reduces noise by 30 to 40 dB in all audio frequency bands. In addition, the dynamic range of the transmission system is expanded, the saturation point of the recording level is raised by 7 to 10 dB as the effective value, level matching and pilot tone are unnecessary because linear logarithmic compression and expansion are carried out, and transient error does not occur even in the case of sudden attack sound.
In addition, the RMS level sensor ensures that the system operates correctly even if the audio signal is out of phase during transmission.
The X-1000R is equipped with a new system of bias oscillation circuit and equalizer circuit EE tapes using magnetic materials for high-density recording, and a new type of high-hardness permalloy head is used for recording and playback, providing excellent sound quality with little change over time.
In addition, the erasing head adopts a double gap with high erasing effect to cope with the large residual magnetic flux density of the EE tape.
In order to make the most of the performance of EE tape, it is equipped with a selector position for EE tape with bias and equalizer set.
The mechanism uses a dual capstan system in which two pairs of capstan and pinch rollers sandwich the tape and drive it. The erasing head is located outside each capstan shaft so that the tension in the loop is always constant and the tape span is shortened.
As a result, both forward and reverse tape travel is stabilized, and modulation noise and flutter components are greatly reduced.
A full-tension servo system is installed to stabilize the running system. As a result, the photointerrupter linked to the tension arm functions to operate the tension servo correctly even when any tape is running, and a constant tape tension is always obtained. This ensures extremely stable running.
Since this mechanism is installed on the left and right tension arms respectively, it operates at the beginning and end of tape winding, forward rotation, reverse rotation, fast forward and rewind operations, and automatically servocontrol the tension.
A full-scale 6-head configuration has been adopted in which each head for recording, playback and erasing is independent for both back and forth operations.
Equipped with a motion sensing mechanism for smooth transition from quick winding to play operation.
Equipped with 1-3, 4-2 track selection queue mechanism.
It is equipped with a real-time pose in which the rise from the recorded pose is smooth.
Equipped with a pitch control mechanism that works for both recording and playback.
It uses an electromagnetic brake to protect the tape.
Equipped with an independent timer switch capable of reverse timer recording.
Equipped with a Oatley berth counter repeat mechanism capable of endless regeneration.
Equipped with a Rec Mute mechanism.
It is equipped with a block repeat mechanism that repeatedly reproduces an arbitrary section.
Since the device is around 40 years old please expect this
video of how the device works is here, just watch
I pack very securely, I use two boxes and a lot of styrofoam and bubble wrap.