SpeedyBee F405 Wing F405Wing APP 2-6S FC Flight Controller ELRS/CRSF Receiver VTX/ Servo BEC WS2812 LED
Product Name: SpeedyBee F405 WING FC board;
-MCU: STM32F405,168MHz,1MB Flash;
-IMU(Gyro&Accelerometer): ICM-42688-P;
-Barometer: SPL006-001;
-OSD Chip: AT7456E;
-Blackbox: MicroSD Card Slot;
-UART: 6 sets(USART1, USART2, USART3, UART4, UART5, UART6(Dedicated for Wireless board Telemetry connection));
-I2C: 1x Used for magnetometer, digital airspeed sensor;
-ADC: 4x (VBAT, Current, RSSI, Analog AirSpeed);
-PWM: 12x (11+1 "LED" pad);
-ELRS/CRSF receiver: Supported,connected to UART1;
-SBUS: Built in inverter for SBUS input (UART2-RX);
-LED: 3xLEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1xRGB;
-RSSI: Supported,Named as RS;
Supported FC Firmware: INAV:SpeedyBeeF405WING(default)ArduPilot: SpeedyBeeF405WING
Product Name: SpeedyBee F405 WING PDB board;
-Input voltage range: 7~36V (2~6S LiPo);
-Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot);
-Battery Current Sensor: 90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot);
-TVS Protective diode: Yes;
-FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS m module, Telemetry module, WS2812 LED_Strip;
-VTX BEC output: Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V Designed for Analog Video Transmitter,Digital Video Transmitter, Camera.
-Servo BEC output: Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, Designed for Servos.
Product Name: SpeedyBee F405 WING Wireless board
Wireless Configuration (long press BOOT button for 6 seconds to switch modes):
-BLE mode, connect to Speedybee APP;
-Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.
-Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner
LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes)
-4x WS2812 LED strip connectors, adjustable colors and flashing modes
-4x WS2812 LED strip connectors, adjustable colors and flashing modes
On-board battery level indicator
-4x RGB indicator LED for battery level display by number of lights
SpeedyBee F405 WING F405Wing APP FC board ICM42688P Flight Controller for RC Fixed Wing Model Airplane
Product Name |
SpeedyBee F405 WING FC board |
MCU |
STM32F405,168MHz,1MB Flash |
IMU(Gyro&Accelerometer) |
ICM-42688-P |
Barometer |
SPL006-001 |
OSD Chip |
AT7456E |
Blackbox |
MicroSD Card Slot |
UART |
6 sets(USART1, USART2, USART3, UART4, UART5, UART6(Dedicated for Wireless board Telemetry connection)) |
I2C |
1x Used for magnetometer, digital airspeed sensor |
ADC |
4x (VBAT, Current, RSSI, Analog AirSpeed) |
PWM |
12x (11+1“LED”pad) |
ELRS/CRSF receiver |
Supported,connected to UART1 |
SBUS |
Built in inverter for SBUS input (UART2-RX) |
LED |
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB |
RSSI |
Supported,Named as RS . |
Supported FC Firmware |
INAV:SpeedyBeeF405WING(default)ArduPilot: SpeedyBeeF405WING |
Weight |
8.9g |
Product Name |
SpeedyBee F405 WING PDB board |
Input voltage range |
7~36V (2~6S LiPo) |
Battery Voltage Sensor |
Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot) |
Battery Current Sensor |
90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot) |
TVS Protective diode |
Yes |
FC BEC output |
Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip |
VTX BEC output |
Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter,Digital Video Transmitter, Camera. |
Servo BEC output |
Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos. |
Weight |
11.4g |
Product Name |
SpeedyBee F405 WING Wireless board |
Wireless Configuration (long press BOOT button for 6 seconds to switch modes) |
BLE mode, connect to Speedybee APP |
Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc. |
|
Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner |
|
LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes) |
4x WS2812 LED strip connectors, adjustable colors and flashing modes |
Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads |
|
On-board battery level indicator |
4x RGB indicator LED for battery level display by number of lights |
Weight |
4.2g |
