This auction is for STM32-QFP100

Yamaichi IC Test & Burn-in Socket with a simple board, specifically designed for STM32 microcontroller in QFP100(0.5mm pitch) package

Features

  • 20-pin JTAG/SWD port and/or 4-pin USART1 interface for programming/testing
  • External crystal can be connected via on board socket for system clock
  • Onboard 32.768K crystal oscillator
  • Two LED indicators for testing, which are connected to the I/O pins via jumpers
  • All the MCU pins are accessible on expansion connectors
    • pin header pitch: 2.54mm(100mil)

Supported Devices

STM32 microcontroller in QFP100(0.5mm pitch) package with compatible pinouts:

  • STM32L1xxV series (STM32L151VB, STM32L152VB, etc.)
  • STM32F1xxV series (STM32F103VE, STM32F100VE, etc.)
  • STM32F2xxV series (STM32F207VC, STM32F215VC, etc.)
  • STM32F3xxV series (STM32F303VC, STM32F373VB, etc.)
  • STM32F4xxV series (STM32F407VG, STM32F415VG, etc.)

Config the onboard "Device selection jumpers" according to the device to be programmed.

Outline and Dimensions

Unit: mm
Part Number Pitch Pins Applicable IC Dimensions (REF.) Outside Dimensions (REF.)
A x B C x D E F G x H
IC51-1004-809 0.5 100 14 × 14 16 × 16 15.3 - 39 × 39

Photos

  1. JTAG/SWD port
    • for programming/debugging/testing
    • compatible with ST-LINK / J-LINK / ULINK2 / STX-RLINK
  2. USART1 port
    • supports ISP and/or serial port debugging
  3. LED indicators
    • for quick testing
  4. Pin headers connected to MCU pins
    • clearly labeled with onboard marks
    • easy for testing and further expansion
  5. Boot mode configuration
    • configuring the BOOT0 and BOOT1 via jumpers
  6. 3.3V onboard regulator
    • AMS1117-3.3
  7. 5V power input
    • DC jack or 2-pin header
  8. External crystal socket
    • insert crystal to the holes on two sides, leave alone the middle hole
  9. Power indicator
  10. Device selection jumpers
    • short the upper headers for STM32L1xx / STM32F1xx / STM32F3xx
    • short the lower headers for STM32F2xx / STM32F4xx
  11. LED jumpers
    • short the jumpers to connect LEDs to MCU I/O pins for testing
    • open the jumpers to disconnect
  12. 32.768K crystal (on bottom side)
    • for internal RTC with calibration

JTAG/SWD Connector Layout

The STM32-QFP100 houses JTAG/SWD headers for connecting a programmer. The connector layout is shown in the figure 1 below.

JTAG/SWD connector layout

Figure 1. JTAG/SWD connector layout

Boot Mode Configuration

Depending on the used pin configuration, the Flash memory, system memory or SRAM is selected as the boot space, as shown in Table 1 below.

STM32 boot mode configuration

Downloads

Development resources:schematic, etc.
Wiki: www.waveshare.com/wiki/STM32-QFP100

Package Contains

  1. STM32-QFP100 × 1
  2. USB power cable × 1
1
2
Purchasing Guide for Adapters & Sockets
Index Package (click belows to BUY it) Socket Dimensions (click belows to cover more)

Adapters with pin header 		General QFP GP-QFP64-0.5...(click)
QFN GP-QFN20-0.5...(click)
Special AVR M48+ ADP...
STM8 STM8-QFP32...
STM32 STM32-QFP48...
PIC PIC SOT23 TO DIP8 (A)...(click)

Adapters to DIP 		QFP QFP32 TO DIP32...(click)
QFN QFN8 TO DIP8 (A)...(click)
SOP SOP8 TO DIP8...(click)
SSOP SSOP8 TO DIP8(A)...(click)
TSOP TSOP28 TO DIP28...(click)
MSOP MSOP8 TO DIP8...(click)
SOT SOT6 TO DIP6 (A)...(click)
PLCC PLCC20 TO DIP20...(click)

Test & Burn-in Sockets 		QFP IC51-0324-1498...(click)
QFN QFN-64BT-0.5-02...(click)
SOP OTS-8(16)-1.27-03...(click)
SSOP OTS-8(28)-0.65-01...(click)
TSOP OTS-32-0.5-01...(click)
MSOP 656-1082211...(click)
SOT 499-P44-10 (REV.B)...(click)
PLCC IC120-0324-009...(click)
DIP DIP 20 Pin ZIF Socket (Green)...(click)
Terms & Conditions
Payment: · PayPal is the only method of payment that we accept.
Shipping: · We ship items to Worldwide!
· Please confirm your address in paypal, phone number is also very important.
· All items will be shipped within 48 working hours on receipt of cleared payment.
· We'll add a tracking number after sending the item so that you can track your parcel.
Returns Policy: · We are happy to return any unused item in its original packaging within 14 days of delivery.
· Buyers are responsible for the round(two-way) shipping cost.
Feedback: · We'll leave POSITIVE FEEDBACK on receipt of cleared payment.
· If you're satisfied with the item and our service, please leave POSITIVE FEEDBACK, it's important to us.
· Once any  problems occured, please contact us first. We'll try our best to work things out.
FAQ: · More details(Click)
If you have any question, please feel free to contact us. It's our pleasure to serve you!
We appreciate your business!