SUZUKI GSXR 600 750
CRASH PROTECTORS MUSHROOMS AND BOBBINS
BLACK SET SENT AS DEFAULT, IF YOU WANT WHITE SET, PLEASE ADD MESSAGE TO SELLER AT PAYPAL CHECKOUT, OR EMAIL ME ONCE PURCHASED
THIS IS A FULL SET OF PROTECTION
FRONT FORK SPINDLE MUSHROOMS (BLACK)
REAR WHEEL SPINDLE MUSHROOMS (BLACK)
FAIRING MUSHROOMS(BLACK)
PADDOCK STAND BOBBINS LARGE 25MM DIA (BLACK)
BRAND NEW SET OF CRASH MUSHROOMS PRECISION MACHINED FROM HIGH DENSITY ACETAL ( CESTILENE HD500) SPECIFICALLY DESIGNED FOR CRASH MUSHROOMS:-
Good sliding properties (SEE GRAPH BELOW)
Strong and rigid
Resistant to amny oils, greases, diesel, petrol and cleaning fluids
Increased surface hardness
Weathering resistant
COME WITH ALL FASTENERS REQUIRED
THE SPINDLE MUSHROOMS MEASURE 48 MM IN LENGTH, MUCH LONGER THAN MANY EBAY SELLERS, WHICH OBVIOUSLEY GIVES YOU EXTRA PROTECTION !
THEY ALSO FIT SIZE FOR SIZE IN THE SPINDLE BORE SO WILL NOT FLOAT ABOUT IN THE EVENT OF A SPILL UN-LIKE MANY EBAY SELLERS OFFER!!
THE SET ALSO INCLUDES FRAME MUSHROOMS MADE FROM HIGH DENSITY acetal AND COME COMPLETE WITH M10 X 1.25 FINE PITCH BOLT (DE-EMBRITTLED SO WILL NOT SNAP ON IMPACT)
BOTH FRAME SLIDERS ARE ENGINE MOUNTED.
This set of sliders will fit on a gsxr 600 / 750 sportsbike. This kit bolts on, needing modifications to Left hand fairing . These sliders bolt into the upper engine mount, replacing the existing bolts.
- Installation Instructions:
Remove your RHD fairings, and find the engine mount locations where the sliders fit.
They are made for a specific location. They will only fit in one place, remove the m10 engine mounting bolt
Insert m10 bolt supplied through the shorter bobbin with the washer behind the bolt head.
Insert the assembly into engine mount recess.
thighten up until you feel compresion, and then tighten and do not exceed 40 nm of torque.
Remove your RHD fairings, and find the engine mount locations where the sliders fit.
Remove m10 engine mount bolt and paint end.
Replace fairing into original psition so the painted bolt leaves a mark on the inside of the fairing.
Drill a small hole in the marked position on the fairing and check it is in the correct position.
Then carefully drill out the fairing with a 25mm tank cutter or similar
Replace fairing
Insert m10 bolt and washer in the longer mushroom and tighten as above.
ALSO COMES WITH A SET OF PADDOCK STAND BOBBINS
They are made from high quality acetal and come with 2 high tensile zink coated countersunk screws with allen key heads.
WILL NOT RUST OR SEIZE IN SWINGING ARM.
PLEASE SEE MY OTHER AUCTION FOR SEPERATE SETS OF MUSHROOMS / BOBBINS
WHATS INCLUDED:-
4 ACETAL CRASH MUSHROOMS (SPINDLES)
4 M8 FLANGED NYLOC NUTS
2 M8 THREADED BAR
2 FRAME MOUNTED MUSHROOM
2 PADDOCK STAND BOBBINS LARGE 25MM DIA
2 COUNTERSUNK M8 BOLTS
Fitting instructions
ALSO AVAILABLE IN WHITE
PLEASE SEE VIDEO BELOW OF A GSXR 1000 WITH JayBee MUSHROOMS FITTED. THIS IS AT CADWELL PARK, JUST AFTER THE MOUNTAIN -ABOUT 50mph.
SEE PHOTOS BELOW THE VIDEO TO SEE HOW MUCH OF THE BIKE IT SAVED
P.S HE BOUGHT ANOTHER SET FROM ME AS HE WAS SO IMRESSED WITH THE LACKOF DAMAGE TO HIS BIKE!
THE MARKS ON THE TANK IS MUCK AND MUD - NO SCRATCHES AT ALL. FAIRING HAS A SLIGHT SCTATCH !
