eBay

DAP-1360/U Wireless N Access Point Repeater Client WDS WISP 300Mbps NEW Original Box

New updated model of DAP-1360 with 2 External Detachable Antennas

Comes with EU Plug.

Description

Wireless Interface
Using the DAP-1360, you can quickly create a wireless network and allow your employees or members of your family to connect to it almost anywhere (in the range of a wireless network). The access point can act as a base station to connect to a wireless network devices operating on the standards 802.11b, 802.11g and 802.11n (at speeds of up to 300 Mbit / s).
The device provides many functions for the wireless interface. The device supports several security standards (WEP, WPA / WPA2), filtration devices to be connected to MAC-address several operating modes (access point, router, client), and allows the use of technology WPS, WDS and WMM.

Access Point Mode
You can use the DAP-1360 mode, the access point to create a wireless network or a wired connection to the router.

Router Mode
You can connect the DAP-1360 mode, the router to a cable or DSL-modem or dedicated Ethernet-line and use a high-speed connection to the Internet for a wide range of professional tasks.

The "client"
The "client" in Access Point mode allows the use of DAP-1360v as a wireless client and as a repeater wireless network in router mode - as a repeater WISP.

Security
In router mode device DAP-1360 is equipped with a built-in firewall. The advanced security functions minimize threats of hacker attacks, prevent unwanted intrusions into your network and access to unwanted websites for users of your LAN.

Easy setup and update
To configure the access point DAP-1360 uses a simple and user-friendly web-interface (available in several languages).
Now you can easily update the firmware - the access point itself is a proven software version on the update server D-Link and notifies the user ready to install it.

Features

Can be flexibly configured to operate as an access point, wireless client, bridge, bridge with AP, repeater, WISP client router or WISP repeater
Complete set of security features including WEP/WPA/WPA2/WPS to safeguard your network against outside intruders
Wireless N draft standard offers an increased range that is six times farther than 802.11g

warranty services from the manufacturer D-Link

Specifications

WAN
• 1-port 10 / 100BASE-TX Ethernet for cable or DSL-modem or dedicated Ethernet-line

LAN interface
• 1-port 10 / 100BASE-TX Ethernet

WLAN interface
• IEEE 802.11n (up to 300 Mbit / s)
• IEEE 802.11b / g

Antenna
• Two detachable 5 dBi omni-directional antennas
• RP-SMA connector

Modes of operation
• Access Point Mode
• Router Mode

Network functions
• Types of WAN-connection
   + PPPoE
   + Static IP
   + Dynamic IP
   + Static IP + PPPoE
   + Dynamic IP + PPPoE
   + PPTP / L2TP + Static IP
   + PPTP / L2TP + Dynamic IP
• DHCP-server / relay
• DNS relay
• Skip VPN-tunnel (PPTP / L2TP)
• Dynamic DNS
• Static IP-routing
• Remote Access
• Network statistics for each interface
• IGMP Proxy
• RIP
• Supports UPnP IGD
• Supports ping from the external network (WAN ping respond)
• Support for SIP
• Support for RTSP
• Skip PPPoE-packet (PPPoE pass through)

Wireless connection
• Supported security standards
   + WEP
   + WPA / WPA2 Personal
   + WPA / WPA2 Enterprise
• MAC-filter
• Management of connected devices
• PIN and PBC methods of WPS
• The WMM (Wi-Fi QoS)
• Advanced Settings
• WDS
• "client" in access point mode
   + Wireless client
   + Repeater Wireless Network
• "client" in router mode
   + Repeater WISP (Wireless Internet Service Provider)

Firewall Features
• Network Address Translation (NAT)
• Stateful Packet Inspection (SPI)
• IP-filters
• URL-filter
• MAC-filter
• DMZ-zone
• The protection ARP- and DDoS-attacks
• Virtual Servers

Configuration and Management
• Web-based interface for configuration and management of multiple languages
• Access via TELNET
• Automatic notification when a new software version
• Update the internal software of the access point via web-interface
• Saving and loading configuration
• Support for remote logging
• Automatic synchronization of system time with a NTP-server and manually configure the date and time
• Ping
• Traceroute

Indicators
• Nutrition
• Wireless network
• WPS
• Local Area Network
• Internet

Power
• Power supply: External power adapter DC 12V / 0.5A

Button
• Power on / off
• Click the button to use the WPS function and return to the factory default settings

Working temperature
• From 0 to 40 ° C

Storage temperature
• -20 to 65 ° C

Operating humidity
• From 10% to 90% non-condensing

Storage humidity
• 5% to 95% non-condensing