BMP280
Druckbereich: 300-1100 hPa (9000 Meter über dem Meeresspiegel auf -500m)
Relative Genauigkeit (bei 950 - 1050 hPa bei 25°C): ±0.12 hPa, equiv. zu ±1 m
Absolute Genauigkeit (bei (950 - 1050 hPa, 0 - +40 °C): ±0.12 hPa, equiv. zu ±1 m
Netzspannung: 1,8 V - 3,6 V
Stromverbrauch: 2,7µA bei 1Hz Ausleserate
Temperaturbereich: -40 bis +85°C
Package included:
Package included:
1x BMP280 Sensor Bord inklusive Stiftleiste
BMP280 MPU9250
Chip: MPU-9250 + BMP280
Power supply: 3-5v (internal low dropout regulator)
Communication: standard IIC / SPI communications protocol
Chip built 16bit AD converter, 16-bit data output
Gyroscopes range: ± 250 500 1000 2000 ° / s
Acceleration range: ± 2 ± 4 ± 8 ± 16g
Magnetic field range: ± 4800uT
Power supply: 3-5v (internal low dropout regulator)
Communication: standard IIC / SPI communications protocol
Chip built 16bit AD converter, 16-bit data output
Gyroscopes range: ± 250 500 1000 2000 ° / s
Acceleration range: ± 2 ± 4 ± 8 ± 16g
Magnetic field range: ± 4800uT
Pressure range: 300-1100hPa
Using Immersion Gold PCB, machine welding process to ensure quality
2.54mm pin pitch
Module size:(L*W)2.05* 1.43cm/0.81"*0.56"
Package Included:1x MPU9250 BMP280 10DOF Acceleration Gyroscope Compass Nine Shaft GY-91 Sensor
Package Included:1x MPU9250 BMP280 10DOF Acceleration Gyroscope Compass Nine Shaft GY-91 Sensor
GY-BME280-3.3V
ME-BME280 is a Breakout Board featuring a Bosch Sensortec ME280 Temperature, Humidity & Pressure Sensor.
The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.
Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k, protocol selector resistor 0ohm (R1), decoupling capacitors 0.1uF on both power supply pins Vdd & Vdd_IO.
If you connect board to both power rails VDD_IO 1.8V and VDD 3.3V be sure to remove the power rail jumper GS1!
BME280 Features
Package 2.5 mm x 2.5 mm x 0.93 mm metal lid LGA
Digital interface I2C (up to 3.4 MHz) and SPI (3 and 4 wire, up to 10 MHz)
Supply voltage VDD main supply voltage range: 1.71 V to 3.6 V
VDDIO interface voltage range: 1.2 V to 3.6 V
Current consumption 1.8 uA @ 1 Hz humidity and temperature
2.8 uA @ 1 Hz pressure and temperature
3.6 uA @ 1 Hz humidity, pressure and temperature
0.1 uA in sleep mode
Operating range -40…+85 C, 0…100 % rel. humidity, 300…1100 hPa- Humidity sensor and pressure sensor can be independently enabled/disabled
Package Included:
The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.
Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k, protocol selector resistor 0ohm (R1), decoupling capacitors 0.1uF on both power supply pins Vdd & Vdd_IO.
If you connect board to both power rails VDD_IO 1.8V and VDD 3.3V be sure to remove the power rail jumper GS1!
BME280 Features
Package 2.5 mm x 2.5 mm x 0.93 mm metal lid LGA
Digital interface I2C (up to 3.4 MHz) and SPI (3 and 4 wire, up to 10 MHz)
Supply voltage VDD main supply voltage range: 1.71 V to 3.6 V
VDDIO interface voltage range: 1.2 V to 3.6 V
Current consumption 1.8 uA @ 1 Hz humidity and temperature
2.8 uA @ 1 Hz pressure and temperature
3.6 uA @ 1 Hz humidity, pressure and temperature
0.1 uA in sleep mode
Operating range -40…+85 C, 0…100 % rel. humidity, 300…1100 hPa- Humidity sensor and pressure sensor can be independently enabled/disabled
Package Included:
1PCS I2C/SPI Breakout Temperature Humidity Barometric Pressure BME280 Digital Sensor
GY-BME280-5V
BME280, the precision sensor from Bosch, is soldered onto PCB.
Not only the pressure and the temperature, this sensor can measure humidity.
It uses both I2C and SPI (supports 3-, 4-wire SPI) interface
Specifications:
Supply Voltage: 1.8 - 5V DC
Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
Operational Range:
Temperature: -40 to +85°C
Humidity: 0-100%
Pressure: 300-1100 hPa
Resolution:
Temperature: 0.01°C
Humidity: 0.008%
Pressure: 0.18Pa
Accuracy:
Temperature: +-1°C
Humidity: +-3%
Pressure: +-1Pa
I2C address
SDO LOW ： 0x76
SDO HIGH： 0x77
Not only the pressure and the temperature, this sensor can measure humidity.
It uses both I2C and SPI (supports 3-, 4-wire SPI) interface
Specifications:
Supply Voltage: 1.8 - 5V DC
Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
Operational Range:
Temperature: -40 to +85°C
Humidity: 0-100%
Pressure: 300-1100 hPa
Resolution:
Temperature: 0.01°C
Humidity: 0.008%
Pressure: 0.18Pa
Accuracy:
Temperature: +-1°C
Humidity: +-3%
Pressure: +-1Pa
I2C address
SDO LOW ： 0x76
SDO HIGH： 0x77
Package Included:
1 x Breakout Temperature Humidity Barometric Pressure BME280 Digital Sensor Modul
Am 30.06.18 hat der Verkäufer die folgenden Angaben hinzugefügt:
Am 09.01.2023 hat der Verkäufer die folgenden Angaben hinzugefügt: