Package include:
100% Brand New and High Quality!!
1)This spindle is built-in type spindle motor, built-in three asynchronous motors,Bythe inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high precision and high stability operation.
2)The bearing of spindle use grease lubricated angular TOcontact bearings,can be achieved lifelong lubricating within the life cycle.
3)The spindle use forced coolling mode TOcoolling motor,front and rear bearings.Coolant flow through the reasonable arrangement cycle watercourse of the spindle body,thus can take the heat generated of the spindle rotation speed, TOachieve thermal equilibrium,let spindle temperature within a certain constant value. External coolingDevice effect:maintaining a constant temperature of the coolant.
4)The spindle built-in PTC 140 temperature sensor(TEchnicalparameters are visible in other sections of this specification),you can read it anytime if you need TOprotect the motor temperature.
5)The tool clamping methods:this spindle built-in automatic tool changeDevice,shank form is BT30.
SpindlemODEL: | RTM120X103-30-24Z/4.5220v | Voltage: | 220V |
Maximum speed: | 24000rpm | rated frequency: | 800HZ |
Electric current: | 15A | MotorPole: | 4Pole |
RAted power: | 4.5KW(S1) | Peak power: | 5.4KW(S6) |
Rated Torque: | 3.5NM | Peak Torque: | 4.2NM |
Productcharacteristic curve graph:
WiringdEfinition
Power Supply, Fhermal, Fan
Proximity switch and push button switch
Details:
TEchnicalparameters | ||
No. | PRoject | Standard |
1 | SpindleblowingDust/seal gas pressure (MPa) | 0.2-0.25 |
2 | Spindlegas seal gas flow (L/min) | 65 + 10 (When onWORKING) |
3 | Cooling water pressure (MPa) | ≧0.25 |
4 | Cooling water flow (L/min) | ≧2.5 |
5 | Cooling water temperature(℃) | 24-28 |
6 | Spindlestatic state pulse(M) | ≦3 |
7 | Spindlevibration (Mm/s) | ≦1.0 |
8 | Spindleassembly method | Bottom mounting(6-M8) |
9 | MotorwindingsPressure test (V/M) | 1000V/1 minute withstanding Voltage test |
10 | Tool Interface | BT1 |
11 | Inverter Specifications | 5.5KW(220V) |
12 | fitment | Woodworking machinery, polishing industry, etc. |
Spindleinstallation explanation
1) Fan cooling systemDescription
When the spindle rotates, the rear fan system must be started TOensure the correct supply voltage and the supply voltage is 12v.
2) Air Sealing control(AS)
In order TOprevent water or impurities enters internal of the spindle,spindle will have gas SealingDevice,the gas seal machine must be started start with the machine at the same time. And the need TOgo throughmulti-stage filtration.
3) Compressed gas quality requirements
The quality requirement of gas whichis used in gas seals:
Oil Content:﹤0.01mg/m³
Solid particle:< 5 * m
PressureDew point:< 7.5Degrees C(0.7mpa)
4) Running-in program instructions
Only all monitoring issued no failures operational signals,at the same time,all safetyDevices have been installed and working properly,then allow start spindle.
Note: new or spindlewhichIs not used for a long time must TObe running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase TO50% of the maximum speed,TOrun 15 minutes,finally, increase TOmaximum speed.It 's need TOcheck the temperature of the spindleDuring the wholeProcess,Spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer serviceDepartment.
5) Productbackend interface instructions
No. | Function | DEfinition |
1 | GAS Sealing(Protection of impurities inTOthe spindle0.2-0.25MPa) | Ф6 |
2 | Return air (piston reset 0.35-0.45MPa) | Ф6 |
5 | Power Supply (Spindlepower lines with thermistor) | U/V/W/ Ground wire |
6 | Intake air (Spindleloose knife0.5-0.6MPa) | Ф6 |
7 | sensor(spindle tool change signals 24V) | Broach / loose knife |
8 | Fan(spindle cooling) | 12v |
6) PTC140Temperature coefficient thermistor parameters
Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection.
Parameter name | Parameter symbol | Single Core | Three core Series connection | Unit |
Maximum DC working temperature | Umax | 30 | 30 | V |
Rated control temperature | TK | Designed according TOuser | ℃ | |
Rated control temperaturetolerance | T1 | ±5℃ | ±5℃ | ℃ |
Rated control temperaturetolerance | T2 | ±0.5℃ | ±0.5℃ | ℃ |
Resistance value on 25℃ | r25 | ≤100 | ≤300 | Ω |
Rated control temperature | TK-5℃ | ≤550 | ≤1600 | Ω |
Rated control temperature | TK+5℃ | ≥1330 | ≥4000 | Ω |
Rated control temperature | TK+15℃ | ≥4 | ≥12 | KO |
Thermal response time | TA | ≤5 | ≤5 | S |
Dielectric Strength | Uis | AC2.5 | AC2.5 | KV |
Maximum control temperature | TKmax | 180 | 180 | ℃ |
Maximum allowable storage temperature | tmax | 180 | 180 | ℃ |
Minimum allowable storage temperature | Tmin | -40 | -40 | ℃ |
7) ProductTool ChangeSignalsdescription
sensor MODEL(0-24V, PNP), The spindle built two sensors.wiring Diagram is as follows:
1. Response broach knife signal, when theKnife handleIs hang,black sensor output signal;
2. Response loose knife signal, when theKnife jawsOpen,black sensor output signal;
5.5KW Fuling Inverter VFD 220v or 380V
Feature:
It could adapt TOtheDust working environment.
Output frequency:0-1000hz
220V Configuration:
Brand Name:Fuling
Power:5.5kw
Rated output current:23A
Output voltage:3phase AC220V
Input voltage:1phase AC220V
Frequency:0-1000HZ
380V Configuration:
Brand Name:Fuling
Power:5.5kw
Rated output current:23A
Output voltage:3phase AC380V
Input voltage:3phase AC380V
Frequency:0-1000HZ
Shipping
USA post service round 10-18 business days
Canada China post round 25-40 business days
Australia China post round 20-35 business days
Western EU(Germany,UK,France, etc) China post 20-35 business days
Asia,South America,other countries Chins post round 15-40 business days
Note:above offer is default delivery way,if you need fast delivery like as DHL/UPS or post service pls inform us to confirm the shipping cost before you bid
Above DHL/UPS offer is without remote fee,if your post code is remote it need extra cost.
Payment
Problem&Feedback
Refund
Contact us