Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply
Features:
Brand new LCD display interface, more intuitive and clearer data display
Brand new MOSFET drive design, providing greater drive current and switching speed
Re-layout of components, more reasonable PCB design
Adopt 4MOSFET design to minimize the problem of MOSFET mismatch
1: 12V car battery from 25 to 40ah, requires good performance and small internal resistance
2: 4000 to 6000mAh 45C to 60C 3S model airplane lithium battery
3:30 to 35ah 12V capacity lithium battery pack
Note: Can not use super capacitor as power supply
Welding nickel strip selection
The thickness of the welded nickel strip should be 0.1 to 0.12mm
Exceeding this thickness may cause the MOS tube to burn out
Energy setting
The energy must gradually increase from 01, and the maximum cannot exceed 30. It is recommended that the energy be below 30.
Exceeding the above conditions may damage the controller!
In the shutdown state, long press the square button, the buzzer will beep three times, and the controller will turn on
In the power-on state, long press the square button, the buzzer will beep twice, and the controller will shut down
There is only one parameter that needs to be set to control the welding energy. The larger the parameter setting, the higher the welding energy.
In the power-on state, use the up and down triangle buttons to set the welding energy parameters
There are three working modes for control STOP MANUL AUTO
STOP: In this state, the controller cannot be welded
MANUL: manual welding mode, welding through an external trigger switch
AUTO: automatic welding, when the soldering pen touches the nickel strip, the delay is 1 second, and the welding is automatically completed
Select the automatic mode, set the energy to 1 first, and then put the nickel belt on the test machine (don’t weld the battery yet)
If the welding is not possible, gradually increase the energy until it can be welded, do not increase the energy
Before completing the welding, make sure that the soldering pen is firmly crimped onto the nickel strip, otherwise it will blow through.
1: Cannot be welded
the reason:
Generally, the battery capacity is too small and the ability to release current is insufficient
Nickel belt is too thick
Solution:
Choose a battery that meets the requirements
Welding nickel tape between 0.1mm and 0.12mm
the reason:
Too much energy
The soldering pen is not firmly pressed
There are flammable materials under the nickel belt
Solution:
Energy down
During the welding process, keep the welding needle completely firmly crimped on the nickel strip
During the welding process, no flammable materials must be placed under the nickel belt
the reason:
Battery capacity is too large
Nickel belt is too thick
Solution:
Choose a battery that meets the requirements
Welding nickel tape between 0.1mm and 0.12mm
Package Included:
Controller X1
Soldering pen X2
Power cord X2
Manual X1
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
Note, read before use！！！！
Battery selection
1: 12V car battery from 25 to 40ah, requires good performance and small internal resistance
2: 4000 to 6000mAh 45C to 60C 3S model airplane lithium battery
3: 30 to 35ah 12V capacity lithium battery pack
Welding materials
Welding 0.1 to 0.12mm thick nickel-plated steel strip
Energy setting
The energy must gradually increase from 01, and the maximum should not exceed 50
Exceeding the above conditions may cause damage to the controller！
1. PayPal payment accepted only.
2. Items will be shipped to your eBay address. Please make sure it is correct.
1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.
2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer.
3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.
When you satisfied with our product and services please leave us positive feedback.
If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay.