1. 3 Output Ports:
Output I is a 5V USB port that can be used to power or charge cell phones, iPhone/iPod/iPod Touch, MP3/MP4 players, PDAs and any other device that can be charged from a USB port (USB power cable not included).
Output II has a nominal voltage of 10.8V (Range from 9V ~ 12.6V). This port's power comes directly from battery cells without voltage regulation. When the battery is fully charged, its voltage is 12.6V. Output voltage will then decrease gradually. Most of the time, the output voltage will be around 10V ~ 11V ( nominal voltage is 10.8V). When the voltage drops to 9V, the port will shut off and stop providing power. This port can be used to power portable DVD players and digital photo frames.
Output III : This port output voltage is regulated 12V. This port can be used to power many different electronic devices that require stable 12V voltage.
2. High Capacity:
This battery has a capacity of 99 Watt-hour.
3. Wide range input voltage:
This battery can be charged from any 12-24V DC power source. It can also use your current laptop AC power adapter as a charger if it has a 5.5 x 2.1mm connector.
Battery Specifications:
| Model:BP90-12V | |
Capacity: | 100 Watt-Hour |
| Battery Cell: | Lithium-ion |
| Input Charging Port: | Input Voltage Range: DC 12 ~ 24V. Connector Size: 5.5 x 2.1mm |
| Outputs: | Port I: 5V USB Port; Maximum Output Current: 2.1A Port II: Nominal Output Voltage 10.8V Output Voltage Range 9V ~ 12.6V Output Connector Size: 3.5 x 1.35mm; >Maximum Output Current: 5A Port III: Output Voltage: 12V Output Connector Size: 5.5 x 2.5mm Maximum Output Current: 5A |
| Charging time /Temperature | 4-6 hours / 0～45 ℃ |
| Size | 186 x 114 x 22.5mm ( or 7.5" x 4.5" x 0.9") |
| Weight: | 621g ( or 1.4 lb) |
| Power Indicator: | 4 level LED indicator |
| Built-in Protection Circuit: | -Over-charge |
| Operating Temperature: | - 20～ 60 ℃ |
| Storage Temperature: | - 20～40 ℃ |
Standard package:
The battery pack comes with one BP90-12V battery + 1 power output cable + AC Charger
The port III output cable has a 5.5 x 2.5mm connector built on. It can be changed to a different size connector by plugging on a BiXPower C series connector tip.
Port I and Port II can use optional connector tips at Consumer Electronics Plug Tips.
If you need more running time, you may connect 2 batteries together in parallel with BiXPower Y25 Split Connector :
Y25 Split Connector Not Included
Cautions: To link two batteries in this way, please make sure:
1. The output voltage of two batteries is set at same.
2. Any single battery has ability to power the powered device by itself.
Only Port III can be linked this way. The purpose of link two or more batteries together is to provide longer running time without interruption. There is no balance control between two batteries . One battery may output more power than another battery and run out of power earlier than another battery. This will not be a problem if a single battery output power is enough to run powered device. However, if the powered device power demand is more than a single battery capability, it may run to problem when one battery run out of power earlier.
Notes: Only a few BiXPower batteries ( such as BP90, BP100, BP160 and BP220 batteries) have been specially designed to allow multi batteries to connect in this way. Other batteries may not be allowed to be connected together in this way (unless specially mentioned).
You may also use multi Y25 Split Connector to Daisy Chain more batteries to provide even more power. Please make sure all batteries output voltages are set at same. Fully charge each battery separately before connect them together.
The battery regular Z6 output cable can fit Y25 connector female end, which will be combined output port in this case. You may use BiXPower Special Cable with On/Off Switch : which can be used power output cable directly without battery regular Z6 output cable.