Battery is not included in the price. It is forbidden to send rechargeable batteries.
!!! For better deal and data find Nautilis eu !!!
The regular color of the iRelay case is black. The color of the Pill case can be blue or green
Ispindel Pill is an electronic hydrometer used for the fermentation of beer or wine.
Its angle changes during fermentation, it reads that angle and
calculates the final gravity (FG) using the previously entered original
gravity (OG). When the device is reset, it opens an access point (AP) to
which you connect with a laptop, mobile phone or tablet. Configuration
is done through the web interface.
During fermentation, the data is
sent over WiFi to a remote computer that collects it. It can be MQTT
broker, Ubidots server, Influxdb, Prometheus push gateway, custom HTTP
TCP / IP server, etc ...
The device has a built-in and digital temperature sensor whose data is sent along with FG data.
The
unit comes without battery. It accepts 18650 Lipos with flat top, or
button top. It also accepts batteries wirh current/under/over voltage
protection, up to 71 mm in length. Inside is a battery charging module
with a one micro USB, and one USB C connector. Charge the device by
unscrewing the lid and connecting it to a mobile phone charger. Inside is also a switch for turning
device off. Charging can be done when iSpindel is powered off.
In this configuration,
the angle will be approximately 27 degrees, which is in the recommended
range of 25-30 degrees.
It has 2x silicone O-ring for better sealing so you can be sure there will be no leaks. The Pill tube was tested at a pressure of 4 bar, or almost 60 psi. There
were no traces of water in the case, and this result provides reliable
assurance for pressure fermentation.
The
unit uses Kegland Pill tube
THIS
IS NOT A KIT. I'm selling a fully functional sample. You mush have your
own 18650 lipo battery for device to work (If you are outside EU). Device has been tested, but
not calibrated. BEFORE USING THE DEVICE, IT IS NECESSARY TO CALIBRATE
IT, following the instructions given on the websites.
Due to its extremely reliable connectivity, iSpindel consumes noticeably less power and thus lasts longer. iSpindel WiFi relay plus is powered by a 5V USB-C cell phone charger that can also be used to charge your hydrometer battery, and your power consumption is negligible. The iSpindel hydrometer no longer needs the Internet, and WiFi relay it doesn’t need either. Now the internet connection is only needed when you need a remote insight into the fermentation state via the previously mentioned applications. The gadget can greatly facilitate and speed up the calibration of the iSpindel hydrometer, as it displays an angle.
The relay firmware is constantly being upgraded and improved. Firmware upgrades, if necessary, they upgrade wirelessly via OTA (Over the Air) and the device’s web interface.
Currently 2 iSpindel hydrometers can be connected to the iSpindel WiFi relay. Any irregularities or warnings on the display are shown in red colour. A confirmation tone sounds when saving the settings and a continuous alarm occurs at too low or too high hydrometer temperature and when the specific gravity falls below the value you specify.
iSpindel relay+ has posibility of entering OG for 2 hydrometers from which % ABV and attenuation are then automatically recalculated. The latest firmware has SG and temperature correction for both iSpindels applied to the Display and Blynk Application.
The battery status of the iSpindel is displayed as a graphic icon showing the battery voltage and as a percentage of the remaining voltage. Next to the battery status icon is a graphic display of the signal strength according to the hydrometer, and next to it is a graphic display of the signal strength according to the home WiFi network. If the Relay is not connected to home WiFi then the “D” (Disconeconnected) mark is visible instead of the signal strength display.
If you use Plato degrees instead of SG, then you can change the density unit for each iSpindel in the settings.
If you accidentally calibrated the iSpindel in the Plato unit, you can convert P to SG in the management settings of relay local web site. This only applies to iRelay, while the application receives the original iSpindle data.
The device only works on 2.4ghz WiFi network.
The outdoor or ambient thermometer has the ability to alarm you when temperature too high or too low is. The length of the sensor can be extended without affecting the measurement. Also, this thermometer can be placed on the fermenter shell and serve as protection against fermentation temperature controller failure (STC – 1000). In the thermometer settings, you can select the unit in degrees C or degrees F.
If the relay has a built-in temperature probe then you can add a BrewSpy new device, Brewfather Custom Stream device or Grainfather custom controller to display temperature on the BrewSpy, Brewfather or Grainfather app. Temperature appears in the interval of 1,5 or 15 minutes and is sent independently of the interval of the iSpindle.
WHAT YOU GET:Due to the ban on posting external links on Ebay, along with the shipment comes a paper with all the necessary links!