Specifications:

Quantity: 2 Pcs

Color: Crystal Clear

Material: Resin

Uses: crystal epoxy production, cos equipment production, RC boat production, DIY glass steel works, reinforcement, etc.

Capacity: 240ML/500ML/1000ML/2000ML/3000ML

Highly transparent, non-yellowing, automatic defoaming

You can make rings, bracelets, pendants, etc. with our glue

You can experience the fun of handcrafting and creativity

Please Note: 

As this product is very pure epoxy. And it acts in a similar manner just like pure honey (epoxies act similar to honey in that, during winter honey is extremely thick and yet in summer, that same honey is very thin and runny). So it is with epoxies. And just like pure honey which sometimes turns to sugar? Pure Epoxy resin can act in a similar way and develop crystals (usually in Part A). this is not from faulty resin but common thought is that it is from the cylic hot days and cold nights when stored.  An easy fix is to heat the jugs up in very hot water for about 30 mins and this will restore the resin to perfectly clear. The heating is also good to help remove air bubbles trapped in the epoxy due to transportation.

NOTE:During the mixing and hardening of epoxy resin AB liquid, heating is normal and will not affect the use, please rest assured. It is recommended that the mixed liquid should not exceed 100ML each time.If you think the temperature is too high, you can use cold water to cool it down.

Usage:

1. Mixed two bottles: A : B = 1:1 ratio(volume ratio).

2. Stirring must be uniform, especially the inner wall of the container, the bottom, etc., about 5 minutes. 

You can use glass rods, bamboo sticks, etc. After mixed,this product is better to let stand for 3-5 minutes 

before used in order to break the bubbles which produced when it was mixing in time.

3. Please try a little bit before using the product a lot, so that would master the skills and avoid mistakes.

4. When using crystal glue, be careful not to stick it on your hands or body. If this happens, wipe off the glue with a cloth or paper towel, then rinse with water soap or detergent.

Question:

Q:Why are there bubbles in the finished product?

A:Stir too fast when adjusting the glue, and pour into the mold before the bubbles have completely subsided. Or after pouring the glue into the mold, the inner wall of the mold is not observed. If there are bubbles, please cut them off in time.

Q:Why is the finished product soft?

A:Inaccurate adjustment of the glue ratio will cause the finished product to not solidify, and the glue will not be thoroughly mixed evenly during stirring, and there will be wire drawing in the glue, and the mold will be demolded if it is not completely solidified.

Q:What should I do if I get Epoxy?

A:It can be washed directly with water, or wiped with a nail remover towel before washing.
Q:Can it be put in the sun or in the refrigerator?

A:Do not expose to the sun for a long time. Excessive exposure to ultraviolet rays will make the finished product fade and yellow. Putting glue in the refrigerator will greatly extend the fixed time.

Package include

Option 1:

1 x A Epoxy Resin(120ML)

1 x B Epoxy Resin(120ML)

1 pair of gloves

1 x Stirring rod

Option 2:

1 x A Epoxy Resin(250ML)

1 x B Epoxy Resin(250ML)

1 pair of gloves

1 x Stirring rod

Option 3:

1 x A Epoxy Resin(500ML)

1 x B Epoxy Resin(500ML)

1 pair of gloves

1 x Stirring rod

Option 4:

1 x A Epoxy Resin(1000ML)

1 x B Epoxy Resin(1000ML)

Option 5:

1 x A Epoxy Resin(2000ML)

1 x B Epoxy Resin(2000ML)