Direct replacement to your original unit
Improved heat sink and charging capabilities
Higher grade of electric components, the quality exceeds the OEM equipment
All shipped products are tested
All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.
PLEASE NOTE : This voltage regulator is ONLY for lithium batteries THIS IS NOT FOR LEAD ACID BATTERIES. Output Voltage is the key factor in a voltage regulator designed specifically for Lithium batteries. The ideal charging voltage for Lithium batteries is 13.9-14.2VDC. The RMSTATOR regulator has a carefully set output voltage of 14.1VDC (+/- 0.1VDC). This stable and ideal output voltage carefully keeps a lithium battery in it?s ideal charging range.
Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product
Protect your investment in an expensive lithium battery with our lithium battery voltage regulator!
Battery condition is important. No regulator can make up for a bad or weak battery. If in doubt charge your battery and have it load tested, or simply replace it. ALWAYS START WITH A FULLY CHARGED BATTERY !
WORKS WITH LITHIUM BATTERIES ONLY
Stop burning your voltage regulator rectifier!
It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all SCR diode-style OEM regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.
Top Features
Opposite connector (main harness side) included as we know these are often melted / corroded / defective and a major cause for repetitive electrical issues.
All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part
Lithium batteries have different charging requirements than Lead Acid or AGM batteries that can severely affect their lifespan and performance. The key factors in safe and reliable lithium battery charging are the output DC voltage ripple and average output voltage. The RMSTATOR regulator is designed around the optimal parameters for these factors.
Charging voltage ripple in a powersports application is the difference between the highest and lowest voltages from the voltage regulator output. By nature, a common shunt style voltage regulator will have a fairly high voltage ripple due to the regulation shunt switches opening and closing frequently. Each on/off transition will cause some variation in the output voltage, this is unavoidable. Keeping this to minimum is critical for Lithium batteries, and the RMSTATOR Lithium regulator is designed around this feature.
In a perfect world, a ripple of less than 10% of the output voltage (~1.5V for a typical regulator), would be ideal, however is not practical for this type of regulator. The RMSTATOR Lithium regulator is able to maintain a less than 4 Volts output ripple, compared to verified test results of our competitors 8 volts. Keep in mind this ripple voltage is only seen via an Oscilloscope sampling the voltage 1000?s of times a second, and is not the same as your average charging voltage as measured by a multimeter.
Runs much cooler than the traditional Shunt voltage regulator rectifier.
Less load on the stator, less work, less fuel is used and you save.
The power charging your battery is steadier and smooth.
Extends the battery’s life and cold cranking capacity.
Removes stator load resulting in more engine power.
Optimize power delivery by switching the stator coils on or off.
With design
This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.
Suzuki LTA 400 KingQuad -- 2010-2013
Suzuki LTF 400 KingQuad -- 2008-2013
32800-14G00
5BN-81960-00-00
32800-20H00
Dimensions:
Width: 89 mm
Length: 91 mm
Height: 27 mm
Fixation holes center to center: 66 mm
Other specifications:
Number of plugs: 1
Number of pins: 6
Number of wires: 5
Minimum Charging Voltage: 14.5 V +/- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20?C to 85?C
Before installing your new CNC Mosfet Voltage Regulator Rectifier :
find parts for :